Bedienungsanleitung Ciclo CM 628i Master (Seite 4 von 16) (Englisch)

588918

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

If the CM 628i fails to display any heart rate, it probably

means that there is no contact between the skin and the

electrodes. Moistening the electrodes and the underlying

skin often helps. Best results are obtained if electrode gel

is used (available from pharmacies).

3 .FUNCTIONALITY OF THE CM 628i

By means of the respective transmitter identification, the

CM 628i can automatically identify on which bike it is

being used.

For this, it is necessary that it is seated on the handlebar

bracket and only in this way is the built-in movement

sensor activated, which then initiates the transmitter

search with the first registered movement of the bike.

During the transmitter search a zero flashes in the upper

display and, if a transmitter is found, the flashing stops.

A non-flashing zero in the upper display means that a

transmitter has been found, however, it is not transmitting

any speed signal at this time i.e. the wheel is at a stand-

still.

The speed transmitter is activated with the first wheel

rotation and the cadence transmitter through the first pedal

rotation.

The transmitter search in the CM 628i can also be started

manually (if the CM 628i is located on the handlebar

bracket), this is done by pressing both buttons simultane-

ously for a short period.

The manual transmitter search functions only if no trans-

mitter has yet been found (' – ' in the upper display).

If a transmitter has already been found, briefly pressing

both buttons simultaneously changes between Bike 1 and

Bike 2.

Only when a speed transmitter has been found (and if the

cadence is switched on – setting adjustment mode 'C on'),

is the relevant cadence also searched for automatically.

If no cadence transmitter is mounted, this function should

be switched off in the setting adjustment mode, since the

cadence transmitter is normally searched for indefinitely

(and this search will drain the battery quicker).

After this the heart rate transmitter is searched (only when

the heart rate is switched on – setting adjustment mode 'H

on').

If heart rate measuring should be started without CM 628i

being on the handlebar bracket, press both buttons short

when lower display shows 'H –'.

magnet. Turn the

transmitter so that

the separation

distance between

transmitter and

magnet is not more

than 3 mm. To

check for correct

installation, rotate

wheel a few times and check whether the computer re-

ceives a signal.

2.3 Installing the optional cadence transmitter

Attach cadence transmitter to a strut opposite the pedal

crank with the aid of the O-ring. Hang the O-ring on one

side of the transmitter, wrap around the strut and hook

back on the opposite side.

Mount the magnets on the pedal crank directly opposite

the transmitter with the aid of the cable tie (do not fully

tighten at this time), so that the magnet points exactly to

the marker on the transmitter. Turn the transmitter so that

the separation distance between transmitter and magnet is

not more than 3 mm. To check for correct installation,

rotate the pedal a few times and check whether the

computer receives a signal. Then tighten up cable ties.

2.4 Putting on the heart rate transmission belt

The transmitter belt is hung in

the elastic chest belt and

fastened around the upper

body. The transmitter (the

plastic part with the company

logo) should lie over the

middle of the upper stomach,

immediately below the breast-

bone, so that the logo on the

transmitter is legible (viewed from the front) (see illustra-

tion). The electrodes in the belt, to the right and left of the

transmitter, must be in contact with the skin.

Pull the belt tight so that it cannot slip and constant con-

tact with the body is guaranteed during movement.

max. 3 mm

Electrodes

Transmitter

02 CM 628i engl 34-65 27.09.2005 8:40 Uhr Seite 8

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ciclo CM 628i Master Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ciclo CM 628i Master

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info