Bedienungsanleitung Ciclo CM 628i Master (Seite 5 von 16) (Englisch)

588918

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Unit of measure kilometers or miles

The preferred unit of measure for

the display can be set here,

kilometers or miles.

Change with right button (save

setting and continue with left

button).

Adjust daily kilometers 1 and 2

Set with right button, save and

continue with left button.

Default = 0 km or last adjusted

value

Setting range min. = 0.00 km

Setting range max. = 999.99 km or

624.99 miles

The daily kilometers can be adjusted here, e.g. as a

starting point in case of tours according to a tour guide-

book, if the tour was not entered at "0" km.

Wheel circumference 1 and 2

Set with right button, save and

continue with left button.

Default = 2080 mm (Bike 1) and

2050 mm (Bike 2) or last adjusted

value

Setting range min. = 0 mm

Setting range max. = 9999 mm

Wheel circumference tire size (mm)

The wheel circumference can be taken from the following

table or measured by yourself.

Tire size Circumference Tire size Circumference

40-559 26 x 1,5 2026 mm 40-622 28 x 1,5 2224 mm

44-559 26 x 1,6 2051 mm 47-622 28 x 1,75 2268 mm

47-559 26 x 1,75 2070 mm 40-635 28 x 1 1/2 2265 mm

50-559 26 x 1,9 2026 mm 37-622 28 x 1 3/8 2205 mm

54-559 26 x 2,00 2089 mm 20-622 700 x 20C 2114 mm

57-559 26 x 2,125 2114 mm 23-622 700 x 23C 2133 mm

37-590 26 x 1 3/8 2105 mm 25-622 700 x 25C 2146 mm

32-620 27 x 1 1/4 2199 mm 28-622 700 x 28C 2149 mm

32-622 700 x 32C 2174 mm

Caution: Whilst not in use, or during transportation of the

CM 628i e.g. in the car, the CM 628i should not remain

on the handlebar bracket. Small movements will activate

the movement sensor and start the transmitter search,

which is a very demanding function on the battery, e.g.

during a car journey of several hours, the battery life is

greatly reduced if the CM 628i is still in position on the

handlebar bracket and the transmitter search is activated

indefinitely by the vibrations of the car during the journey.

4. BASIC SETTINGS

If the CM 628i is to be used with 2 bikes, some adjust-

ments must be carried out separately for each bike.

Ensure the respective Bike number is displayed before

adjustments are commenced.

The heart rate measuring is independent from the set bike,

so the values set for heart rate measuring are valid for bike

1 and bike 2.

For all adjustments, the following applies:

The flashing value can be changed with the right button, by

short pressing of the left button this value is stored and the

next value to be adjusted flashes or the next display

appears.

The current adjusting mode can be prematurely ended by

pressing the left button for 3 seconds.

All adjustments and displays always refer to the

corresponding bike (Display ➀ or ➁).

4.1 Adjusting the unit of measure,

the wheel

circumference, the daily/total kilometres, switching

on and off the cadence and switching on and off the

heart rate measuring

Select the required bike (➀ or ➁) through short simultane-

ous pressing of both buttons.

Then press the right button shortly

until the following display appears:

By pressing the left button for 3

sec., this display now appears:

02 CM 628i engl 34-65 27.09.2005 8:40 Uhr Seite 10

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ciclo CM 628i Master Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ciclo CM 628i Master

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info