Bedienungsanleitung Ciclo CM 628i Master (Seite 7 von 16) (Englisch)

588918

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

46 47

If the 12-hour display is selected later, the CM 628i con-

verts the time automatically.

Setting the year

Set with right button, save and

continue with left button.

Year range = 2000 - 2099

Setting the day/month

Set with right button, save and

continue with left button.

Day range = 1 - 31

Month range = 1 - 12

Now the current date can be set

(with 24-hour display in the day/month format, with 12-

hour display in the month/day format).

The following adjustment (Chap. 4.5) appears only if the

cadence has been switched on (see Chap. 4.1).

4.5 Initialization of the cadence transmitter

Press the right button until the

following display appears:

By pressing the left button for 3

sec., this display now appears:

Initialization of the cadence transmitter

The initialisation display for the cadence appears in the

display (= Cadence).

If no cadence transmitter has been initialised for the actual

bike, start the initialisation now (see below).

If a cadence transmitter has already been initialised,

change into the operating mode through short pressing of

the left button.

Before the transmitter search, allow the magnet to pass in

front of the cadence transmitter once (1 pedal rotation).

This will start the Transmitter and emit a signal for approx.

3 minutes.

Start the transmitter search in the CM 628i by pressing

both buttons for a short time.

A percentage value runs up in the

display during the initialisation (see

Fig.)

After a successful initialisation, the

CM 628i changes automatically into

the normal operating mode and the indication SPD/AV

appears in the display.

In the case of an unsuccessful

initialisation (see Fig.), the

transmitter search can be started

again by repeated short pressing of

both buttons.

The initialisation can be interrupted after a fault by short

pressing of the left button, the CM 628i then switches to

the normal operating mode.

Pay attention during the initialisation that no second speed

transmitter is located nearby (currently active).

A transmitter already initialised to Bike 1 cannot also be

initialised for Bike 2 (or vice-versa).

4.4 Setting the time and date

Press the right button shortly until

the following display appears:

By pressing the left button for 3

sec., this display now appears:

Time-of-day display: 24-hour

or 12-hour (AM/ PM) indication.

Adjust with right button (save and

continue with left button).

If the 12-hour indication is selected,

a "P" appears before the time in

case of PM time.

Setting the time

Adjust with right and left button

(save and continue with left button).

Time range = 00:00 - 23:59

Here the current time is set in the

24-hour format. (If the 12-hour

display had been selected,

00:00 - 12:59 AM/PM can also be entered; a "P" appears

before the time in case of PM time)

02 CM 628i engl 34-65 27.09.2005 8:40 Uhr Seite 14

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ciclo CM 628i Master Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ciclo CM 628i Master

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info