Bedienungsanleitung Ciclo CM 628i Master (Seite 6 von 16) (Englisch)

588918

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

44 45

4.2 Setting of the service interv

Press the right button until the

following display appears:

By pressing the left button for 3 sec,

this display now appears:

Setting of the service interval

Set with right button, save and continue with left button.

Default = 1000 (km or 625 miles) or the remaining value

up to the next service.

Range = 0 - 9999 km or 6249 miles

The service interval can be adjusted here, e.g. after how

many kilometers travelled should the brakes be checked or

similar. The service interval will count down until it reaches

zero. The service symbol will then appear in the

display.

Following this, a new service interval can be entered. The

service symbol is then deleted from the display.

4. 3 Initialization of the speed transmitter

Press the right button until the

following display appears:

By pressing the left button for 3

sec., this display now appears:

Initialization of the speed transmitter

The initialisation display appears.

If no speed transmitter is initialised (e.g. after a battery

change without power-saving mode, or if the CM 628i is to

be used on a second bike), start the initialisation now by

short pressing of both buttons (see below).

If a speed transmitter has already been initialised, change

into the operating mode through short pressing of the left

button.

Before the transmitter search, allow the magnet to pass in

front of the speed transmitter once (1 wheel rotation).

This will start the Transmitter and emit a signal for approx.

3 minutes.

Measurement of the wheel circumference (U)

(for more precise adjustment):

Make a marker on the front tire and on the floor (e.g. with

chalk). Move the bike straight ahead by exactly one tire

rotation (for a more precise measurement ensure tire

pressures are correct and be seated on the bike) and mark

the location on the floor. Now measure the distance exactly

between the two markers on the floor to give you the

wheel circumference (in mm)

Adjust total kilometers 1 and 2

Set with right button, save and

continue with left button.

Default = 0 km or last adjusted

value.

Setting range max. = 99999 km or

62499 miles.

The total amount of kilometers travelled up to now can be

adjusted here.

Cadence On/Off switching (ON/OFF)

Switch On and Off with right button

(continue with left button).

Here, the cadence can be switched

On and Off. The cadence should be

switched on only when a cadence

transmitter is also used (mounted),

since the CM 628i will normally

search for the relevant transmitter

indefinitely.

The default setting is 'oFF'.

Heart rate On/Off switching (ON/OFF)

Switch On and Off with right button

(continue with left button).

Here, the heart rate measuring can be

switched On and Off. The heart rate

measuring should be switched on only when a heart rate

transmitter is also used, since the CM 628i will normally

search for the relevant transmitter indefinitely.

The default setting is 'on'.

▲

02 CM 628i engl 34-65 27.09.2005 8:40 Uhr Seite 12

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ciclo CM 628i Master Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ciclo CM 628i Master

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info