Bedienungsanleitung Consolar Control 601 (Seite 15 von 63) (Englisch)

743662

Zoom out

Zoom in

Vorherige Seite

1/63

Nächste Seite

TDMA CONTROL 601/701:

Published 07/2007

2.5.3 Return Flow Temperature Raising

Main Menu 12:34

Heating Input

Both the CONTROL 601 and the CONTROL 701 have a

programmable temperature difference regulating function

which can be used to control the hydraulic system’s return

flow temperature raising.

Return Flow Temp. Raising Difference:

2...24 K

The temperature difference by which the temperature of

the return flow temperature raising sensor of the thermal

store must be higher than that at the return flow sensor can

be set here. This activates the „Return Flow Temperature

Raising“ function (the switch over valve is switched to AB-

A). The hysteresis is set at 2K in the factory.

ADVICE:

Attention must also be paid to the „Back up heating via

CONTROL“ function on page 6 with the „Return flow

temperature raising“ function.

Temperature difference switch:

Input – Function – Output

Sensor description

Function

Return flow temperature

raising thermal store sen-

sor

(Art. N

. RE 046)

Return flow temperature rai-

sing

Return flow temperature

sensor

(Art. N

. RE 046)

Return flow temperature rais-

ing

Winter switch over

Output: Return flow temperature raising (Switch over valve)

2.6 Boiler Operating Functions (Boiler Input

Data)

Main Menu 12:34

Boiler Inputs

All settings for the boiler (e.g. oil or solid fuel) , the boiler

pump and the thermal store loading pump are entered

here.

2.6.1 Boiler (Oil, Gas, Pellets)

The hydraulic system switch controls the operation of either

the boiler pump or the thermal store loading pump. The

relationship is as follows:

Regulator setting

automatic switching to

Buffer logic

Boiler pump

Return flow tempera-

ture raising

Thermal store loading pump

No setting

Thermal store loading pump

Boiler Temperature

minimum : 0...70 °C

The minimum temperature at which the boiler or thermal

store loading functions are activated is set here.

Boiler temperature

maximum : 50...90 °C

The maximum boiler temperature at which the boiler

(burner) will be switched off via the zero voltage contact or

the 0 – 10V interface is set here.

Boiler difference

maximum: 0....60 K

Heating Operation: The temperature difference between

the calculated heating target temperature and the buffer

logic difference (when the Buffer logic function is activated)

and the actual boiler temperature is entered. When the

actual boiler temperature is higher than the target tem-

perature by this set temperature difference the burner will

switch off.

Hot Water Back up Heating Operation: The temperature

difference between the hot water target temperature and

the actual boiler temperature is set here. When the actual

boiler temperature is higher than the target temperature by

this set temperature difference the burner will switch off.

Example: Boiler heating

Heating circuit target temperature:

50 °C

Hot water back up heating target

temperature:

55 °C

Boiler Difference Maximum:

15 K

If during hot water back up heating operation the boiler

reaches a temperature of 70 °C, the boiler will switch

off. During heating operation the boiler will switch off at

65 °C. However, when the Buffer logic function is acti-

vated (e.g. Buffer logic difference : 6 K), the boiler will

switch off at 71 °C.

Boiler Input: Single stage / modulated op-

eration

This function enables single stage or modulated operation

of the boiler.

Single Stage Operation: The boiler is switched on and off

via the zero voltage contact.

Modulated Operation: The boiler is controlled via a volt-

age of between 0 to 10V. The voltage depends ofn the

temperature difference between the target and actual

boiler temperature.

The following 6 menu points are only to be found in the

professional menu for modulated boiler operation.

Minimum : 2...50 k W

Boiler Capacity

The minimum boiler capacity for modulated boiler regula-

tion is set here.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Consolar Control 601 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info