Bedienungsanleitung Cube SL (Seite 6 von 6) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

657573

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

Reifengröße Umfang

40-559 26 x 1,5 2026 mm

44-559 26 x 1,6 2051 mm

47-559 26 x 1,75 2070 mm

50-559 26 x 1,9 2026 mm

54-559 26 x 2,00 2089 mm

57-559 26 x 2,125 2114 mm

37-590 26 x 1 3/8 2133 mm

32-620 27 x 1 1/4 2199 mm

40-622 28 x 1,5 2224 mm

47-622 28 x 1,75 2268 mm

40-635 28 x 1 1/2 2265 mm

37-622 28 x 1 3/8 2205 mm

20-622 700 x 20C 2114 mm

23-622 700 x 23C 2133 mm

25-622 700 x 25C 2146 mm

28-622 700 x 28C 2149 mm

32-622 700 x 32C 2174 mm

OPERATING MANUAL

Congratulations on your purchase!

With the CUBE SL you have acquired a wireless electronic bike computer with state of the art electronics,

the highest level of precision and it is weatherproof. As special features the SL has an optional cadence

measurement and an optional heart rate measurement (for this you need separately available accessories ).

The Two in One-System: this allows you to use this cycle computer for two different bicycles and view the

combined total values.

Please read this operating manual carefully.

USA

Package content:

- CUBE SL

- battery type CR 2032

- battery cap

- handlebar bracket

- transmitter

- cable ties for mounting

- spoke magnet

1. Mounting

The handlebar bracket can be mounted on the handlebar and also

on the stem.

Bild A: Mounting is possible on handlebar (Position A-1) or stem

(Position A-2).

Bild B: For using it on the stem, change bracket mounting

orientation from Position A to Position B.

Remove the protective tape.

Place the handle bar and fasten it with the cable ties.

Bild C: Mount the transmitter with ca

ble ties on the fork (max.

distance to the handlebar bracket max. 60 cm; best mounting on

the right side, handlebar bracket and transmitter should be on the

same side).

Bild D: Fix the magnet on a spoke so that it will face the mark on

the transmitter. Adjust the magnet position and fine tune the sensor

if necessary (distance between transmitter and magnet max. 3

mm).

Bild E: Rotate the SL to 45 degree left and install it into the

bracket. Then rotate it 45 degrees right to lock it. To unlock, rotate

45 d

egrees to the left.

1.1 Mounting of optional cadence-set

(separately available)

Mount the handlebar as described above on the handlebar or on

the stem.

Place the sensor on the cable on the left chain-brace in height

of the crank with help of cable-ties so that it is still loose enough

to be lined up. Mount the cadence-magnet (with help of a cable

tie) on the inside of the crank. The distance between magnet and

sensor should be max. 3 mm.

The magnets must point directly to the mark on the se

nsor. Now

switch on the cadence measuring in the setting mode of the

SL (see chap. 2.1). Turn crank a few times to check if the mounting

is correct. Now tighten the cable-ties.

1.2 Putting on the heart rate transmission belt

Warning: whoever carries out sport should have a general medical

check up on his/her general state of health - especially beginners,

persons older than 35 years of age and anyone who has suffered

from illnesses or injuries in the past. It is recom mended that a

doctor be consulted in any case in the presen

ce of risk factors,

such as smoking, high blood pressure, high cholesterol values,

diabetes, lack of exercise and excess weight.

Pacemaker wearers should consult their doctor before

using any heart rate measurement device!

The transmitter belt is hung in the elastic chest belt and fastened

around the upper body. The transmitter (plastic part with the CUBE-

logo) should lie over the middle of the upper stomach, immediately

below the breastbone, so that the logo on the transmitter is legible

(viewed from the front) (see illustration). The electrodes in the belt,

to th

e right and left of the transmitter, must be in contact with the

skin. Pull the belt tight so that it cannot slip and constant contact

with the body is guaranteed during movement.

If the SL fails to display any heart rate, it probably means that there

is no contact between the skin and the electrodes. Moistening the

electrodes and the underlying skin often helps. Best results are

obtained if electrode gel is used (available from pharmacies).

Measurement of the heart rate is only possible if the transmitter

belt is fitted correctly and the SL is within the transmitter’s

reception range (max. 60 cm).

2. Preparation

Inserting the battery

Insert battery type CR2032 with plus-pole facing up. Close battery

cap with a coin, being sure not to over tighten. After inserting the

battery the display will show normal mode.

(If nothing or incomprehensible signs appear in the display, press

the AC-button on the rear of the computer with help of a ballpoint

pen or a similar object. Attention: this will delete all values and

setting).

2.1 Settings

Enter setting mode by p

ressing centre button for 3 seconds.

Display shows ‘SET BIKE1’.

To quit setting mode press again centre button for 3 seconds in

any setting.

(To change the display to german language, press left button short,

display shows ‚LANGUAGE’. Press centre button to choose this

function and then switch between ‘English’ and ‘Deutsch’ with right

button. To store press left button and then get back to setting mode

with short pressing of right button).

Though SL can show german and english words, this manual

shows both possible displays.

The different setting modes can be shown by

pressing right

or left button, by pressing centre button the shown setting

mode is chosen.

Possible setting modes:

SET ALT / SET HOEHE

SET BIKE1 / SET RAD1

SET CLOCK / SET UHR

SET HR / SET HF

SET MISC

EXIT / ENDE

LANGUAGE / SPRACHE

Each setting mode can have different setting possibilities.

The following is valid for these settings: the blinking value

can be changed with the right button, the value is stored by

shortly pressing the left button and the next value blinks or

the next value appears on the display.

For a better reading in the following chapters the setting modes are

fat printed and

the settings fat and italic.

SET ALT / SET HOEHE

To define altimeter settings.

To select, press the centre button.

ALTITUDE / HOEHE

To change current altitude

Range: -300 to +6000m

Set with right and left buttons, continue with left button

Here you can change the altitude that is displayed, e.g. if you

notice that the current altitude diverges from altitude shown in the

display (e.g. if barometric pressure changes).

HOME OFF / HEIM AUS

To switch the home altitude on/off

Default: OFF

Set with right button, continue with left button

Here you can switch t

he automatic reset off the home altitude

value on/off

HOME ALT / HEIMHOEHE

Range: -300 to +6000m

Set with left or right button, continue with left button

SL has got a barometric altimeter which adapts itself to

temperature variations.

Changes of barometric pressure (e.g. during the night) can cause

variations of the indicated altitude in the display. To compensate for

these variations you can set the altitude of your origin (e.g. starting

point such as home). With each reset of the daily values (deletion)

the current altitude will be reset to the

adjusted altitude.

UNIT m

Set unit of measurement for altitude

Default: m (meters)

Here you can select whether the indication is meter (m) or feet (ft).

UNIT °C

Set unit of measurement for temperature

Default: °Celsius

Here you can adjust whether the indication is Celsius (C) or

Fahrenheit (F).

SET BIKE1 / SET RAD1

Set of bike-specific values, e.g. total distance, circumference, unit

and more for bike 1.

Choose with centre button.

To do these settings for bike 2, press right and left button short

simultaneously in normal mode.

SL switches to bike 2, then enter

again setting mode (display then shows SET BIKE2/SET RAD2).

DAY DST / TAGES-DST

Set of the daily distance

Default: 000.00 km

Range: 000,00 to 999,99 km or m

Set with right and left button, store with left button.

Here the daily distance can be adjusted, e.g. the point of starting a

tour, when using a printed tour-guide.

(This setting doesn’t change the total distance. There only really

ridden kilometres are counted).

TOT DST / GES. DST

Set of the total distance

Default: 0000 km

Range

: 0 to 99999 km or m.

Set with right and left button, store with left button.

Here the total distance can be adjusted.

Wheel/Radumf.

Set of circumference

Default: 2080 mm

Range: 1000-3999 mm

Set with right and left button, store with left button.

Here the circumference can be adjusted.

The circumference of the wheel can be taken from the

chart (Pict. G) or be measured by yourself.

Measuring the circumference of the wheel (for a more precise

setting):

Put a marking at the front-tire and on the ground (e.g. with chalk).

Ride straight ahead exactly o

ne turn of a tire (for a very exact

measurement, check the pressure of the tire before getting on

your bike) and mark this position on the ground. Now measure the

exact circumference of the wheel between the two markings at the

ground (in mm) – see pict. F.

Unit km bzw. Unit mi

Set of the measuring unit (kilometres or miles)

Default: km

Set with right button, store with left button

Here you can choose whether the display should show kilometres

(km/h) or miles (m/h).

CAD OFF/TRITT AUS

Switch cadence on/off

(ON/AN – OFF/AUS)

Default: OFF/AUS

Set with right button, store with left button

Here you can switch on/off the cadence measuring. To use this

function you need the optional cadence-set (available at your local

dealer).

SET CLOCK / SET UHR

Set of clock, date and clocktime-format.

Choose with centre button

Time / Uhrzeit

Set of clock

Range: 00:00 to 23:59 or 12:00 to 11:59 A/P

Set with right and left button, store with left button

Here you can set the current clocktime. First you set the hours,

then the minutes.

Year / Jahr

et of the year

Default: 2007

Range: 2007 to 2099

Set with right button, store with left button

Here you can set the current year.

Month / Monat

Set of the month

Default: 01

Range: 01 to 12

Set with right button, store with left button

Here you can set the current month.

Day / Tag

Set of the day

Default: 01

Range: 01 to 31

Set with right button, store with left button

Here you can set the current day.

Clock / Zeit

Set of the clock format

Default: 24

Set with right button, store with left button

Here yo

u can select between 24- or 12-hour format (AM/PM).

SET HR / SET HF

Adjustments for the optional heart rate measurement. To use this

function you need the optional heart rate-set (available at your local

dealer).

HR OFF/ON / HF EIN/AUS

Switch heart rate on/off (ON/AN – OFF/AUS)

Default: OFF/AUS

Set with right button, store with left button

Here you can switch on/off the heart rate measuring.

Fitness / Fitness

Adjustment of the fitness level.

Default: 3

Set with right button, store with left button.

Range 1-4, corresponding to the following levels:

1 – poor fitness

2 – average fitness

3 – good fitness

4 – high fitness

Here you set your personal fitness level, necessary for the

CUBEInZone

-calculation.

Sex / Geschlecht

Set with right button, store with left button.

Change between

m = male and f = female.

The sex is needed for the CUBEInZone

-calculation and the

calorie consumption.

Weight / Gewicht

Range: 20 to 220 kg

Set with right and left button, store with

left button

The weight is needed for the CUBEInZone

-calculation and the

calorie consumption.

Birthdate /Gebjahr

Adjust with right and left button, store with left button

Default: 1960

Range: 1920 to 2006

The year of birth is necessary for the CUBEInZone

-calculation.

InZone

Here you can start the CUBEInZone

-calculation by short pressing

of right and left button simultaneously (see also chap. 4 for

CUBEInZone

In order to ignore the calculation, just press short left button.

In order to obtain an exact calculation of ones personal

CUBEInZone

it is necessary to insert the personal data relative to

fitness-level, sex, weight and birthdate.

In order to calculate the CUBEInZone

position the chest belt

correctly, take up a rest position (remain seated and relaxed) and

start the CUBEInZone

calculation by short pressing of right and

left button simultaneously.

The SL will then start to time 5 minutes. During this time, stay

seated, relaxed and calm, as the SL will measure the minimum

heart rate reached during this period (heart rate at rest) and will

store this value

for the subsequent calculation.

After the 5 minutes the lower value of the calculated personal

CUBEInZone

appears in the display.

Lower HR / untere HF

A lower heart rate limit can be set here or (after CUBEInZone-

calculation) the calculated value is shown.

When the current heart rate is lower than this value, the SL shows

an arrow (

) as an optical alarm.

Range: 0 to 220 bpm

Adjust with right and left button, store with left button

Upper HR / obere HF

An upper heart rate limit can be set here or (after CUBEInZone

calculation) the calculated value is shown.

When the current heart rate is higher than this value, the SL shows

an arrow (

) as an optical alarm.

Range: 0 to 240 bpm

Adjust with right and left button, store with left button

Max HR / Max HF

Shows the maximum heart rate, calculated with CUBEInZone

Range: 0 to 240 bpm

Adjust with right and left button, store with left button

SET MISC

Here you can switch on the powerdown-mode or make a reset

(delete all values).

Choose with centre button

Powerdown / STROMSPAR

Switch on the powerdown-mode (e.g. before changing of the

battery, to save the values).

To switch it on, press right and left button short simultaneously,

displa

y fades out and SL is in powerdown-mode. By short pressing

of any button, SL starts again and displays normal mode.

Reset / Löschen

Here you can delete all values (including the total values). For this

press right and left button short simultaneously, display shows

‘reset’ and then normal mode.

If you only want to delete the day values, press right and left button

for three seconds in normal mode.

3. Functions

The SL has an automatic start/stop when on the handlebar bracket.

That means, 4 sec. after the first wheel

turn the display shows

normal mode and the current speed.

1 minute after the last wheel turn (and without a button is pressed)

the display changes to an “energy save“ mode. During this mode,

only the time is displayed.

If the wheel turns or a button is pushed, the computer will resume

normal functions.

SL has got three modes: Bike 1, Bike 2, and Non-Bike mode.

To switch from one mode to another, simultaneously press

the right and left buttons briefly (switching is only possible if speed

= 0).

The centre display shows

or depending on whether the

selected mode is Bike 1 or Bike 2. The Non-Bike mode doesn’t

show any figures in the display. The Non-Bike mode can be used

for tours without a bike (e.g. with a dedicated wristlet). It only

shows values which have nothing to do with the bike movements.

The optional heart rate measuring works also without speed signal:

when SL is in normal mode (by pressing any button or auto-start),

the heart rate receiver is automatically switched on.

And as long as a heart rate is show

n in the display, there is no

automatically switching to sleep mode.

To reset all day values, press right and left button for three

seconds.

The SL has a three-lined display. In the centre part the current

speed is shown, with a small

or left beside, that shows

whether the current values are valid for bike 1 or bike 2.

To advance the functions of the upper display, press right

button, to advance the functions of the lower display press left

button.

Always short pressing of the centre button shows the sub-

functions of the function in the lower display.

Important for all sufunctions: display shows settings for 10

seconds befor switching back to main function.

Functions of upper display:

TM – Daily Ride Time (pict. 2)

DST – Daily distance (pict. 4)

Altitude (pic. 3)

HR (

)

Time (pict. 1)

Function of centre display:

SPD – Current Speed

Inidcates the current speed in km/h or m/h .

Range: 0 to 199,9 km/h or m/h

An arrow on the left side of the display displays, whether the

current speed is faster (arrow up) or slower (arrow down) than the

current average speed.

Functions of lower display:

DST – Daily Distance (pict. 5)

Displays the distance ridden up to now in kilometres or miles..

Range: 0 to 999,99 km or mi

TOT – total distance (pict. 6)

Sub-function “Daily Distance”

Displays the total distance ridden up to now in kilometres or

miles

(since last reset or battery change).

Range: 0 to 99999 km or mi

TOT – sum of total distance of bike 1 and bike 2 (pict. 7)

Sub-function of “Daily Distance”

Displays the sum of the total distance ridden up to now in

kilometres or miles (since last reset or battery change) of bike 1

and bike 2.

Range: 0 to 199999 km or mi

Current Altitude (pict. 18)

Displays the current altitude (above sea level). The altitude is

displayed in intervals of 1 meter. It is determined by the baro-

metric pressure. For this reason, the altitude value is dependent on

weather variations.

Range: -300 to +600

0 m or ft.

Attention! The altitude values will be added together from the

signals received from the bike. In the Non-Bike mode they will be

added together during the whole time.

Daily distance of altitude upwards (pict. 19)

Sub-function of „Current Altitude“

Displays the altitude travelled upwards.

Range: 0 to 20000 m or ft

Daily distance of altitude downwards (pict. 20)

Sub-function of „Current Altitude“

Displays the altitude travelled downwards.

MAX – maximum altitude (pict. 21)

Sub-function of „Current Altitude“

Displays maximum altitude of the tour.

Range: -300 to +6000 m or ft.

TOT – total of altitude

upwards (pict. 22)

Sub-function of „Current Altitude“

Displays total distance of altitude upwards

Range: 0 to 20000 m or ft

TOT – total altitude downwards (pict. 23)

Sub-function of „Current Altitude“

Displays total distance of altitude downwards

Range: 0 to 20000 m or ft

TOT sum of altitudes from Bike 1 and Bike 2 (pict. 24)

(This function doesn’t exist in No-Bike mode)

Sub-function of „Current Altitude“

Displays sum of altitude upwards.

Range: 0 to 20000 m or ft

Current ascent / descent (pict. 25)

Displays current ascent or descent as percentage. The symbol on

the left side of the display shows whether it is ascent (

) or

descent (

). Range: 0 to 100%

Attention: For technical reasons, the current percentage will only

be shown after 50 - 100 m. This depends also on your speed.

Average ascent (pict. 26)

Sub-function of „Current ascent/descent“

Displays the average of the ascent values recorded so far.

Range: 0 to 100%

Average descent (pict. 27)

Sub-function of „Current ascent/descent“

Displays the average of the descent values recorded so far.

Range: 0 to 100%

Maximum Ascent (pict. 28)

Sub-function of „Current ascent/descent“

Displays the maximum of the ascent values

recorded so far.

Range: 0 to 100%

Maximum Descent (pict. 29)

Sub-function of „Current ascent/descent“

Displays the maximum of the descent values recorded so far.

Range: 0 to 100%

Ø – Average Speed (pict. 8)

Displays the current average speed in km/h or mi/h.

Range: 0 to 199,9 km/h or m/h (the decimal place is highranking)

MAX – Maximum Speed (pict. 9)

Sub-function of “Average speed”

Displays the highest speed so far in km/h or mi/h.

Range: 0 to 199,9 km/h or m/h (the decimal place is highranking)

Temperature (pict. 30)

Displays curre

nt temperature

Range: -10 to +50 °C or °F

Attention: If you carry the SL on your body, the measured

temperature can vary from outside temperature.

MIN – Minimum Temperature (pict. 31)

Sub-function of „Temperature“

Displays minimum measured temperature.

Range: -10 to +50 °C or °F

MAX – Maximum Temperature (pict. 32)

Sub-function of “Temperature”

Displays maximum measured temperature.

Range: -10 to +50 °C or °F

Time (pict. 10)

Displays the current time.

Range: 00:00:00 to 23:59:59 or 12:00:00 to 11:59:59 AM/PM

Date (pict. 11)

Sub-function of “Time”

Displays the curren

t date (dd.mm.yy).

TM – daily ride time (pict. 12)

Displays the current daily ride time.

Range: 0 to 9:59:59 h

TOT – total ride-time (pict. 13)

Sub-function “Daily Ride Time”

Displays the total ride time (since last reset or battery change).

Range: 0 to 999:59 h

TOT – sum of total ride time of bike 1 and bike 2

(pict. 14)

Sub-function of function daily ride time

Displays the sum of the total ride time (since last reset or battery

change) of bike 1 and bike 2.

Range: 0 to 999:59 h

The following functions (heart rate and calorie con-

sump tion) only appear, if heart rate is switched on in the

setting mode (for the measuring of heart rate you need the

separately available heart rate-set).

HR - heart rate (pict. 36)

Indicates the current heart rate (bpm = beats per minute)

Range: 0 to 250 bpm

n the right side of the lower display an arrow shows, whether the

current heart rate is below (

), within ( ) or above ( ) the set

heart rate limits.

Ø - average heart rate (pict. 37)

Sub-function of heart rate function

Indicates the average heart rate (since last reset).

Range: 0 to 240 bpm

MAX - maximum heart rate (pict. 38)

Sub-function of heart rate function

Indicates the maximum heart rate reached (since last reset).

Range: 0 to 240 bpm

Training time below the lower limit set for heart rate

(pict. 39)

Sub-function of the heart rate measurement function.

Displays the training time during which heart rate dropped below

the lower limit set.

(since last reset).

Range: 0 to 9:59:59 h

Trai

ning time within the limits set for heart rate (pict. 40)

Sub-function of the heart rate function.

Indicates the training time during which heart rate was within the

limits set (since last reset).

Range: 0 to 9:59:59 h

Training time above the upper limit set for heart rate

(pict. 41)

Sub-function of heart rate function.

Indicates the training time during which heart rate exceeded the

upper limit set (since last reset).

Range: 0 to 9:59:59 h

kCal - Calorie consumption (pict. 42)

Indicates the current calorie consumption (since last reset).

Range: 0 to 99999 kCal

TOT - total calor

ie consumption (pict. 43)

Sub-function of calorie consumption function

Indicates the total calorie consumption (since last reset or battery

change)

Range: 0 to 99999 kCal

The following function only appears, if switched on in the

setting mode (for the measuring of the cadence you need the

separately available cadence set).

CAD - cadence (pict. 33)

Indicates the current cadence (rpm = rounds per minute)

Range: 0 to 250 rpm

Ø - average cadence (pict. 34)

Sub-function of function cadence

Indicates the average cadence.

Range: 0 to 250 rpm

MAX - maximum cadence (pict. 35)

Sub-function of function cadence

Indicates the maximum reached cadence.

Range: 0 to 250 rpm

4. CUBEInZone

-Philosophy and use

CUBEInZone

is a solution for the very best personalisation of your

training routine.

It is possible t

o calculate the optimum training threshold with the

CUBEInZone

function on the basis of your personal data and your

pulse rate when at rest.

CUBEInZone

is the ideal solution for personalised cardio training

applied to any sport, from jogging and cross-country running to

road and indoor cycling.

Improve your fitness? – Lose weight? – Train whilst always taking

your health into consideration? Everyone will find the correct aim to

follow in their training. But how do you train to achieve those aims

in t

he most efficient possible manner? How do you find the right

intensity of effort during the training? CUBEInZone

is the optimum

training ZONE for effort, resistance and weight loss.

What does CUBEInZone

do?

It calculates the optimum training zone for effort, resistance and

weight loss.

The values vary from person to person and they offer a valid

training support – always staying between 70 % and 85 % of the

maximum heart rate.

(+/- 5% of tolerance, taking into consideration the actual heart rate

when at rest and the level

of training).

The question of burning fat is seen in the “correct” light with

CUBEInZone

– on the basis of the personal data collected.

5 . Battery change

SL: Open battery cap with a coin (unscrew to the left). Insert

battery type CR2032 (please use battery with smooth minus-pole)

with plus-pole facing up. Close battery cap, being sure not to over

tighten. After inserting the battery the display will show normal

mode.

If nothing or incomprehensible signs appear in the display, press

the AC-button on the rear of the computer with help of a ballpoint

pen or a similar object. Attention: this will delete all values and

setting.

(Battery change in the optional chest belt works in the same way.)

Trans

mitter: Open battery cap at the top of the transmitter with a

coin (unscrew to the left), remove old battery and insert new 12 V

battery, type 23A (with pluspole facing up). Close battery cap, being

sure not to over tighten.

Please do not throw away battery in your normal garbage.

6. Trouble shooting

Faulty or no display

- check to see if battery is installed properly or replace battery

(Attention: removing battery will clear all settings and values in

the SL)

- press AC-button on the rear of the computer

Speed not displayed

- check to see if wheel-sensor is mounted properly

check the position of the spoke magnet (max. 3 mm distance to

wheel-sensor)

- make sure SL is mounted in bracket correctly

- check wheel circumference

Speed to high or to low

- check wheel circumference

- check to see if you are using miles or kilometers

Incorrect display of altitude:

- Check the home altitude (basic settings). Perhaps the settings

were made incorrectly.

- Changing barometric pressure as a result of changing weather

(readjust current altitude)

No heart rate displayed or values displayed are incorrect

or unstable

- proof whether heart rate is switch

ed on in setting mode

- Check transmitter belt (battery)

- Skin too dry or cold

- Distance between SL and transmitter belt is too great (max. 60

cm)

Cadence is not displayed or value incorrect or unstable

- Check whether switched on in setting mode

- Check sensor and magnet for correct installation

7. Guarantee

We offer a guarantee for 24 months from the date of purchase on

the SL. The guarantee is limited to material and processing faults.

The batteries are excluded from the guarantee.

The guarantee is valid only if the computer

, with accessories, has

been handled and maintained carefully and according to operating

instructions.

To return the SL under conditions/terms of the guarantee, please

refer to your dealer, your local distributor or send the computer with

the proof of purchase (date) and all accessories and with sufficient

postage, to:

Please read through the instruction manual carefully before

sending us your computer and check the battery. An exchange-

device or the repaired device will sent back to you free of charge

if justifiable guarantee-claims have come into question. Please

contact our local distributor.

Repair: If your SL is sent in fo

r repair (or battery change) or if a

guarantee claim is not valid, repairs up to EUR 19.- will be carried

out automatically. In case of higher repair costs you will be notified.

The repaired device will be sent back COD.

Disposal of Old Electrical & Electronic Equip ment

(Applicable in the European Union and other Euro pean

countries with separate collection systems)

This symbol on the product or on its packaging indicates that this

product shall not be treated as household waste. Instead it shall

be handed over to the applicable collection point for the

recycling

of electrical and electronic equipment. By ensuring this product

is disposed of correctly, you will help prevent potential negative

consequences for the environment and human health, which

could otherwise be caused by inappropriate waste handling of this

product. The recycling of materials will help to conserve natural

resources. For more detailed information about recycling of this

product, please contact your local city office, your household waste

disposal service or the shop where you purchased the product.

Guarantee certificate:

Sender:

Name

First name

Street, No.

Code/Location

Telephone (during the day)

Fax

E-Mail

Reason for return:

After expiry of the guarantee: Repairs should be carried out up to a

value of Euro ____________

CUBE Service

Pending System GmbH & Co KG

Ludwig-Hüttner-Str. 5-7

D-95679 Waldershof

Tel.: +49 9231 97007 80

Fax: +49 9231 97007 60

info@CUBE.eu

www.CUBE.eu

Cube SL Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info