768190
29
Zoom out
Zoom in
Vorherige Seite
1/44
Nächste Seite
7.0 MENU AND PICTURE SETTING
R699740 - DreamBee User Manual 29
Gamma
Gamma is the relationship between the color values of the data and the color values displayed. The Gamma
coefficient makes it possible to adjust the brightness of the midtones only without affecting the very bright and very
dark areas. If gamma is set too high, middle tones appear too dark. If it's set too low, middle tones appear too light.
The Gamma correction factor can be set to Normal, A, B or C.
MENU
Image
Gamma
Offset
The Offset function is used to adjust the black level. Adjust the Offset values for each color channel between -30
and +30 (red, blue and green).
MENU
Image
Offset
red / blue / green
Pixel Adjust
The pixel adjust can fine-tune the overall image position and the panel alignments up to +/- 3 pixels horizontally and
+/- 2 pixels vertically. Modifying the optical lens shift may require a pixel adjustment.
MENU
Image
Pixel Adjust
7.4 Setup Menu
Image Profile
An Image Profile defines a set of values that customize a picture setting. These values are stored into memory in
Cinema, Natural Dynamic, User 1, User 2 and User 3 Image Profiles. The following parameters can be adjusted and
memorized:
Contrast
•Brightness
Color
Sharpness
DNR
Color Temp.
Gamma
Offset
See “Custom Image Profile”, page 30 for more details.
Profile Memory
Profile memory menu is used to save, clear or reset an Image Profile stored into memory. See “Custom Image
Profile”, page 30 for more details.
Picture Position
Picture Shift setting
When projecting images with black bands at the top and bottom (cinema image), use this to move the image up or
down while retaining one of the black bands at the upper or lower end. The default value is 0 (Off) and can be set
from -30 Screen Masking
Mask adjustment affects only the edges of the projected image and are used to frame the projected image on to the
screen and to hide or black out unwanted information and noise. The masking can be set to 0% (off), 2.5% or 5%).
MENU
Setup
Picture Position
HDMI Input Level
The HDMI input level function is used to setup the HDMI 1 and HDMI 2 input terminals. It can be set to:
Standard, for normal circumstances, typically using a video source with HDMI output.
Enhanced. select this setting when the black and white of the picture is unclear with RGB video signals from DVI
devices. MENU
Setup
HDMI Input Level
Standard / Enhanced
29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für DreamVision DreamBee wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info