Bedienungsanleitung EasyAlarm CONTROL (Seite 17 von 32) (Englisch)

515345

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

7.4 Supervision mode

LED: acoustical monitoring inactive

LED: acoustical monitoring activated

LED: inactive mode

7.5 Alarm

7.5.1 .. independent of alarm unit state (armed or disarmed)

active on„Default value“

Cause of alarm

I II III

Entry-Delay Connection mode Announcement

Emergency (Sensor-2)

  

Delayed Hands-free connection „Emergency call activated“

Sensor-3

  

Un-delayed Listening-in connection „Alarm due to sensor 3“

1.) Default values without en without consideration of user specific programming in accordance to section 5

2.) Emergency call activation according to section 5.2.2: An emergency call will be triggered, if the button has been

activated for one second. After a pre alarm period of 20 seconds EasyAlarm

starts dialling calling number(s) and a

hands-free connection is established. During the pre warning period the alarm can be cancelled by pressing the

emergency button respectively by pressing key 0..

3.) Sensor-3 activation according to 5.3.1.

7.5.2 .. only if alarm unit is armed

active on

„Default value“

Cause of alarm

I II III

Entry-Delay Connection mode Announcement

Sensor 1

  

Un-delayed Listening-in connection „Alarm due to sensor 1“

Presence verification

  

10 Minutes/30

Seconds

Hands-free connection

„Alarm due to presence

verification“

Sensor 2

  

Un-delayed Listening-in connection „Alarm due to sensor 2“

Noise (Babyphone)

  

Un-delayed Listening-in connection „Alarm due to noise“

Mains power loss

  

1 Minute Hands-free connection „Alarm due to power failure “

4.) Sensor-1 activation according to 5.1.1.

5.) Sensor-1 can be used to verify if a person is present ( section 5.1.2), i.e. an alarm will be triggered if no motion is

detected within 24h. Before starting the alarm there is a pre warning period of ten minutes. If activation is detected

(motion detected or emergency button pressed) within this period, the alarm is cancelled, otherwise EasyAlarm

establishes a hands-free connection

6.) Sensor-2 activation according to 5.2.1.

7.) Noise monitoring according to 5.4: To avoid false alarm while acoustical monitoring, close windows and try to

eliminate sources of noise.

8.) EasyAlarm

monitors mains voltage and triggers an alarm if power loss is longer than 10 to 20 minutes (=> time-out

according to section 10.4). During a pre warning period of 1 minute the following message is announced „Alarm due

to power failure“. After this period EasyAlarm® dials the programmed number and a hands-free connection is

established. If EasyAlarm® does not detect mains power during start up the monitoring remains inactive => „Power

failure“ is announced ! As soon as mains power is detected, EasyAlarm® starts to supervise mains power

7.5.2.1 alarm release renewed

After an alarm EasyAlarm® remains inactive during a waiting period of two minutes. Only if at expiration of this

waiting period an alarm event occurs again, a new alarm is released.

Note:

 After an alarms through to sensor-1/2/3 a renewed alerting comes off only if to the alarm contact returned to the state

of rest.

7.6 Alarm delay / Pre warning period / Entry delay

An alarm can be delayed due to following reasons:

 An alarm sensor in the area of the entrance must be delayed to have enough time to switch off the supervision mode

before EasyAlarm® dials the first calling number.

 A pre warning announcement is used to avoid false alarms (i.e. technical error like power failure, unwanted

emergency calls). During the pre warning period the alarm can be cancelled by pressing the emergency button

respectively by pressing key 0..

 Announcement: „Alarm acknowledged“

Notes:

 The entry/exit period can be adjusted according to section 10.3.

 If an alarm has been triggered by pressing the emergency button, cancellation of the alarm is only possible, if the

button has been released for min. 3 seconds before pressing it again.

7.6.1 Siren activation during pre warning period

If you use a siren ( section 11.2) which is activated as described in section 10.5.2, the pre alarm period is signalled by a

periodical siren tone.

Noise

Nois

4 seconds

4 seconds 4 seconds

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

EasyAlarm CONTROL Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von EasyAlarm CONTROL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info