Bedienungsanleitung EasyAlarm CONTROL (Seite 18 von 32) (Englisch)

515345

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

7.7 Phone connection

The colour of the indicator LED changes to orange during telephone connection.

7.7.1 Time-out

There is a timer running in the phone connection mode. Phone connection is kept up for two minutes in case of alarm call,

and ten minutes in case of test call. Ten seconds before disconnection, the called person hears the announcement “abort”.

He/she can restart timer using DTMF 3 at any time.

7.7.2 Announcements

At the beginning of each phone connection the following information will be announced: Individual message followed by

the cause of alarm and the instruction to acknowledge alarm by pressing DMTF 0 . In a Listening-in connection you get

announcement: „to speak press 1“. This announcement is repeated every 8 seconds, until a tone-dialling command is

entered.

Notes:

 At the beginning of any phone connection battery state will be checked and announced if low

 At the beginning of any phone connection battery state and main voltage are checked. In case a test is negative an

appropriated message will be announced.

 The numbers of unacknowledged alarms is announced.

7.7.3 Listening-in connection

Possible tone-dialling commands during the listening-in connection

DTMF => Every valid command will be signalled

0 Terminate phone connection and acknowledge alarm

1 Switching to hands-free mode and restart connection time-out

2 Repeat announcements (Individual message / Cause of alarm)

3 Restart connection time-out (2 minutes)

4 Deactivate output (i.e. switching off alarm siren)

5 Announcement of current supervision mode as well as condition of the output

6 Activate output (i.e. switching on the alarm siren)

7 Change to inactive supervision mode (I, II, III) => monitoring for noise, sensor-1, sensor-2, mains failure and

presence verification inactive. Emergency call and sensor-3 alarm are still possible.

8 Terminate phone connection without acknowledgment

9 Change to active supervision mode (I, II, III) => All monitoring functions re-activated

* * 0 Announcement of calling number sequence

* * n Announcement of calling number n (n = 1..9)

Following tone-dialling command can be used for remote programming, provided the programming is not blocked (

section 10.6)

* * # Trigger an alarm for test reasons  Cause of alarm announcement "alarm due to programming"

* * <n> * followed by the new calling number announcement and change of calling number n

* * # # Record individual message => according to section 6.3.1.

7.7.3.1 Use of siren during listening in connection

The activation of a siren ( section 11.2) can be done either manually during a listening-in connection using DTMF 6 or 4

or automatically in accordance to the reason of the alarm ( programming section 10.5.2).

7.7.4 Hands-free connection

The commands during hands-free connection are identical to the commands by listening in connection, except DTMF 1 .

Important note:

 Hands-free connection must be terminated using DTMF 0 or 8 . Otherwise a busy tone signal appears until

phone connection is terminated due to time-out.

 By selecting hands-free connection an activated siren (optionally) is automatically deactivated. If requested, the

siren can be activated or deactivated by DTMF 6 or 4 .

7.7.4.1 Adjustment of hands-free volume

During hands-free connection you can increase volume by pressing local key #. or decrease by pressing locale key *..

Level can be adjusted in fifteen steps (1dB each) and remains stored.

7.7.5 Acknowledge alarm / Terminate connection

A called party can choose between acknowledgment by pressing DTMF 0 or passing on alarm to next party in calling

number sequence by pressing DTMF 8 .

Important notes:

 There is no alarm repetition, if an alarm is triggered by pressing any key of the alarm unit (test call).

 An alarm can be confirmed and terminated by pressing key 0. of the alarm unit or by pressing the wireless

emergency button for a second time.

 If the alarm is programmed to a pager, the called person can confirm alarm during remote-access after

dialling-in.

7.8 Alarm repetition

If an alarm has not been acknowledged by passing all the calling numbers in the sequence, a number of alarm repetitions

can be programmed ( programming 10.2). Factory setting: two alarm repetitions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

EasyAlarm CONTROL Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von EasyAlarm CONTROL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info