Bedienungsanleitung EasyAlarm CONTROL (Seite 20 von 32) (Englisch)

515345

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

8. USEFUL NOTES

8.1 Tone-dialling command

If you want to use EasyAlarm® to its full potential a tone-dialling telephone is necessary. Nowadays most of the

telephones in use are working on tone dialling, also called DTMF or in-band signalling. Older telephones are using pulse

dialling. In case there is no tone-dialling telephone available, the features shown in section 7.7.3 cannot be used

Note:

 An acoustic coupler can be purchased in electronic shops.

8.2 User information

8.2.1 Signals (beeps)

A single beep tone is used as a confirmation

Three beep: Mains power loss AND battery low at the same time!

8.2.2 Announcement audible in loudspeaker of EasyAlarm®

Announcement Message / Cause

„Individual message“ First message in case of an alarm

Abort Disconnection caused from the change of the position of the selection switch

Alarm due to presence

verification

Triggered emergency call due to loss of presence

Alarm acknowledged Disconnection

Battery error Battery is low => battery test after power on

Calling number n Calling number n (=1..9)

Calling number error First calling number in the calling number sequence is not programmed

Calling number sequence Calling number sequence

Emergency call activated Emergency call, initiated by emergency button

Emergency call deactivated,

alarm acknowledged

Emergency call confirmed

Error Incorrect programming => the old value remains stored

Line check error Telephone line check after power on was negative => dial tone missing

Output activated The output is activated after power on.

PIN Request to enter PIN-Codes by locked programme

Power failure Mains power missing => Mains power is tested after switching on the unit

Presence verification activated Motion sensor is set to presence verification

Programming deactivated: PIN Request to enter PIN-Code to unlock programming

Supervision (I/II/III) <due to

noise/sensor n> activated

Announcement of the monitored alarm functions at current position of the selection

switch (I/II/III) triggered by pressing key 5. during the inactive waiting period(

section 7.3.1.1)

Supervision (I/II/III) activated Announcement in active supervision mode at current position of the selection switch

(I/II/III)

Supervision (I/II/III) deactivated Announcement in active supervision mode at current position of the selection switch

(I/II/III)

to modify press * , to stop press # Recording of individual message

Unacknowledged alarms: n Quantity of unacknowledged alarms

8.2.3 Announcements audible in the handset of called subscriber

as well as during hands-free connection in loudspeaker of EasyAlarm®

Announcement Message / Cause

„Individual message”

First message in case of an alarm or reaction on DTMF 2 .

Abort Phone connection will be terminated

Alarm due to noise Alarm triggered by noise activity (Note: according to selection switch position

I,II,III the alarm can be delayed)

Alarm due to presence

verification

Triggered emergency call due to loss of presence

Alarm due to programming A test call was initiated due to remote programming ( section 10.8.2)

Alarm due to sensor n

 sensor n activated

 sensor failure

Reason of alarm: alarm contact n.

 sensor n is in alarm mode

 disconnection of sensor during operation

Battery error Battery is low => battery test before phone connection is established

Emergency call activated Emergency call, initiated by emergency button

Emergency call due to sensor Emergency call triggered due to loss of presence verification

Output <activated / deactivated>

confirmation of < DTMF 6 / DTMF 4 > (  section 11.4)

PIN Request to enter PIN-Code after dialling in (remote access)

PIN error, abort Wrong PIN-code => Phone connection terminated

Power failure Mains power loss => Mains power is tested every time before phone connection is

established

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

EasyAlarm CONTROL Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von EasyAlarm CONTROL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info