Bedienungsanleitung EasyAlarm CONTROL (Seite 19 von 32) (Englisch)

515345

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

7.9 Test call

If alarm unit is switched to ON it is possible to start a test call as follows:

1. Select calling number by pressing key <n> (n= 1. .. 9 )

 Announcement: „Calling number <n>“ => If selected calling number is not programmed the message

“Error” will be announced and the first calling number will be dialled instead

2. Wait until hands-free connection is established and speak

3. Terminate phone connection by pressing 0. or slide function switch to OFF

Notes:

 After ten minutes phone connection will automatically terminate if called party does not give any tone-dialling

commands (i.e. called subscriber can disconnect using DTMF 0 or restart timer using DTMF 3 ).

 During inactive waiting period after power on key 9. and 7. activate or deactivate the monitoring of the

supervision. Key 5. starts the announcement of the current supervision mode.

 The volume of hands-free connection can be adjusted as described in section 7.7.4.1

7.10 Dialling-in (check call)

If the alarm unit is switched to ON you can dial in from any telephone set as follows:

1. Dial phone number of the EasyAlarm®

2. Let it ring for two ringing cycles and disconnect (hang up)

3. Redial after 20 seconds => EasyAlarm® answers call after two ringing cycles and waits for the PIN-Code

After entering the correct PIN-Code EasyAlarm® establishes a listening-in connection

 Announcement „to stop press 0, to speak press 1“

If no tone-dialling command is entered, the phone connection will be terminated after two minutes connection time-out.

The supervised person can also terminate the phone connection by pressing the emergency button.

Important: In case that there are unconfirmed alarms, the quantity as well as the last reason of the alarm will be

announced! An unacknowledged alarm will be confirmed by entering DTMF 0 !

Notes:

 The two-step dialling in procedure is for security reasons to avoid detecting of the alarm unit coincidently by an

unknown caller. Direct dialling in as well as other number of ringing cycles can be selected ( section 10.7)

 If the PIN-code is incorrect or not entered within 15 seconds, EasyAlarm® disconnects after the announcement „PIN

error, abort“ => try again and enter correct PIN.

 PIN-code is factory set to 9797. For safety reasons we recommend changing PIN-code and program your individual

code according to the manual.

 If a successful dialling-in should be signalled with five gong-signals (to alert/inform the supervised person),

EasyAlarm® can be programmed according section 10.7.3.

7.11 Answering an incoming call

An incoming call, signalled by a parallel connected phone, can be answered as follows (Function switch ON):

7.11.1 ..by pressing the emergency button

a hands-free connection is established => Disconnect by pressing the emergency button once again.

7.11.2 ..by pressing any key of the alarm unit

a hands-free connection is established => Disconnect by pressing key 0..

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

EasyAlarm CONTROL Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von EasyAlarm CONTROL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info