Bedienungsanleitung Elro HA68S (Seite 22 von 34) (Englisch)

536725

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

CALL ATTEMPTS

This sets the maximum number of times that the dialer will attempt to contact

the central monitoring station.

If the dialer contacts to the central monitoring station once successfully, it will

stop dialing.

Default setting: 3

Scroll through the menu until ‘:3 Call Attempts’ is displayed. The current

setting will also be displayed.

To change the setting press .

Enter the required number (1-5).

Press to save and exit, or

Press to exit without saving.

ARM/DISARM BY USER

This determines when user makes a selection for disarming (Open) or arming

(Close) the system, an event code 401 is needed to be sent to the central

monitoring station. When setting to ‘On’, an event code 401 will be emitted,

setting to ‘Off’, an event code 401 won’t be emitted.

Default setting: Off

Scroll through the menu until ‘:4 ARM/DISARM By User’ is displayed. The

current setting will also be displayed.

To change the setting press .

Press to commence sending the event code.

Press to commence not sending the event code.

REMOTE SYSTEM CONTROL SETUP

Scroll through the manual until ‘4-3 Remote TEL Control Setup’ is displayed

and press .

Note: After completing the Remote Tel Control Setup, press to return to

the top level programming menu.

-45--20-

EXTERNAL CONNECTIONS

The Control Unit incorporates a terminal block for connection of hard-wired

Zones (33-36), Siren or Telephone Dialer unit. The connection terminal block is

located inside the Control Panel behind the front cover.

To access the terminal block Press

this puts the system into Test Mode and prevents an alarm occurring. Undo the

two fixing screws on the top edge of the Control Panel and open the front cover.

Before making any connections, ensure that the memory jumper link P1 is in

the ‘OFF’ position and then remove the DC power jack and disconnect one of the

back-up batteries.

Hardwired zone and tamper switches

should be Volt free and Normally

Closed, with the contacts opening in

order to initiate an alarm.

Note: Jumper link P51 should be

fitted into the ON position only if the

external hardwired tamper circuit is

used, otherwise it must be in the OFF

position.

After making your external

connections reconnect the power

supply and Back-up Battery. Then

close the Control Panel cover and

tighten the fixing screws on the top

edge of the Control Panel.

Terminal Block

ENEN

Hardwire siren termina,there

is output voltagein OUT

position when alarm mode

(siren setting in ON mode)

DC power output terminal

V+ has power voltage output

Relay output terminal,

accept other N.C. or N.O.

devices

Battery power pack input,

option 12V DC battery input

to increase system stand by

life time

Negative tamper return,

normal close, system can be

detected once circuit close

Hard-wired zones for trigger

onput terminal, use standard

hard wire magnetic, there

are 4 sets of hard-wired

zones: T1(zone7), T2(zone8)

T3(zone9), T4 (zone10)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elro HA68S Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elro HA68S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info