Bedienungsanleitung Elro HA68S (Seite 23 von 34) (Englisch)

536725

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

DIGITAL DIALER SETUP

Scroll through the menu until ‘4-2 Digital Dial Setup’ is displayed and press

Note: After completing the Digital Dialer Setup press to return to the top

level programming menu.

PHONE NUMBER

Scroll through the menu until ‘:1 Phone No:’ is displayed. The current setting

will also be display.

To change the setting press .

Enter the phone number (32 digits max. ranging from 0~9, *, #, ).

Press to save and exit, or

Press to exit without saving.

Notes:

Press to insert a 3.6s pause in the dialing sequence.

Press to move the cursor left.

Press to move the cursor right.

Press to delete the character under the cursor.

Press and hold to erase the entire phone number.

UNIT ID NUMBER

This helps central monitoring station set an ID number for the user whose

system is connected to their center.

Scroll through the menu until ‘:2 Unit ID No:’ is displayed. The current setting

will also be displayed.

To change the setting press .

Enter the ID number (4 digits max. ranging from 0-9, B, C, D, E, F)

Press to save and exit, or

Press to exit without saving.

-21--44-

INITIAL TESTING

As the system is initially installed it is recommended that each device is tested in

turn as it is installed, (refer to testing instructions for particular device).

TESTING AN INSTALLED SYSTEM

The Control Panel has a programmed test routine. You may test the system at

any time, however it is recommended that the system is tested at regular

intervals not exceeding 3 months.

With the system in Disarm Mode

Press This puts the system into Test Mode.

User Password

Use the and buttons to scroll through the menu and press to select

the displayed test function or sub-menu.

Note: After completing all required test functions, press to leave Test mode

and return to Disarm mode.

WALK TEST

Before commencing testing, please ensure that there is no movement in any PIR

protected area, all doors/windows protected by Magnetic Contact Detectors are

closed and that all battery covers and housings are correctly fitted.

Scroll through the top level Test Mode menu until ‘WALK TEST’ is displayed and

press . ‘Walk Test Waiting…’ will be displayed.

1. Trigger each detector on the system by either walking into a PIR protected

area or by opening a door/window protected by a Magnetic Contact detector.

As each detector is triggered the Control Panel will chime to indicate that an

alarm signal has been received and the identity of the zone that the detector

is configured for will be displayed.

2. Operate detector anti-tamper switches by opening the case of the device. As

the switches are operated the Control Panel will chime and zone name will be

displayed.

3. Activate each button on the Remote Control in turn. As each button is pressed

the Control Panel will chime and the button name will be displayed. (e.g.

‘REMOTE CONTROL DISARM’).

Press to exit Walk Test and return to the top level Test Mode menu

TESTING THE SYSTEM

ENEN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elro HA68S Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elro HA68S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info