807226
9
Zoom out
Zoom in
Vorherige Seite
1/20
Nächste Seite
9
Remove both cross-headed screws from the rear cross-bracket of the
bicycle rack.
Insert the screws into the license plate holder and screw  rmly to
be bicycle rack as shown in Figure 5. Ensure that the license plate
is centred and at the same height as the lights for the license plate.
Figure 4: License plate holder
Figure 5: Mounting the license plate holder
5.1.2 MOUNTING THE LICENSE PLATE HOLDER
The mounting clips (5) for securing the license plate are push-out
parts in the holder. Break out two of the clips. Slide the license plate
into the holder, then push the clips into the cut-outs (6) to secure
the license plate.
Figure 6: Mounting the license
plate
In order to unfold the bicycle rack, start by swivelling the rear
lights outwards. The light mounts are clipped onto the rack table.
Pull the light mounts out of the clips. Pull the locking mechanism
back (Position 1 in Figure 12). Hold the locking mechanism in this
position. Swivel the light mount out fully (Position 2 in Figure 12).
Now release the locking mechanism (Position 3 in Figure 12), the
light mount is now secured to prevent it from folding back in.
5.2 DISMANTLING THE BICYCLE RACK
Figure 12: Locking the light mounts
Fold open the bicycle rack as shown in the following Figures.
1. Fold out the right rear light
3. Fold out the right wheel rail
2. Fold out the left rear light
4. Fold out the left wheel rail
1. Fold out the right rear light
2. Fold out the left rear light
3. Fold out the right wheel rail
4. Fold out the left wheel rail
Figure 13: Screw base
Ensure that the trailer tow bar is undamaged, clean and free of
grease. Remove any paint from the coupling ball.
The bicycle rack is placed with the base horizontally on the trailer
tow bar from above. Insert the screw M16 (Position 1 in Figure 13)
into the base (Position 2 in Figure 13). Tighten the M16 screw slight-
ly and align the bicycle rack parallel to the rear of the vehicle. Now
tighten the M16 screw with the installation wrench in such a way
to ensure that the rack is securely attached and can no longer be
rotated.
Regularly check the  rm seating of the rack on the trailer tow bar as
well as the functionality of the lighting systems.
5.3 MOUNTING THE BICYCLE RACK ON THE TRAILER TOW BAR
Slight signs of pressure on the tow bar ball are
normal and do not in uence the functionality.
9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Eufab 11569 - Crow Basic wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info