Bedienungsanleitung Ferm MSM1040 (Seite 11 von 160) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Türkisch)

762257

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

Do not under any circumstances use

grinding discs as the cutting tool.

Before replacing the saw blade, it is strongly

advised to set the mitre angle and bevel angle to

0°. Otherwise, access could be limited.

• Disconnect the machine from the power supply.

• Remove the screw (33) that holds the retraction

arm to the blade cover.

• Remove the screw (40) in order to remove

the bolt-cover by lifting the blade cover (5)

upwards.

• Both saw blade bolt (42) and Flange (41) should

be visible now like shown in fig. E.

• Press the saw blade lock button (43) Rotate

the saw blade carefully by hand until the blade

locks.

• Use hex key to remove the saw blade bolt (42)

by loosening in a clockwise direction.

• Remove the Flange (41) and the saw blade

• Replace the saw blade making sure that the

arrow marked on the saw blade must point in

the same direction as the arrow shown marked

on the machine. The saw blade teeth must

point downwards.

• Fix the saw blade bolt (42) use the saw blade

lock button (43) in order to secure tightly

• Lower the blade cover (5) in order for the bolt

cover to fall back into place and tighten the

screw (40)

• Attach the retraction arm back onto the blade

cover (5) by tightening the screw (33)

• Rotate the saw blade and check if the guard

operates freely

Dust extraction

Fig. A, B, T

Provide good ventilation at the

workplace.

Wear dust protection.

The dust from materials such as lead paint and

some types of wood can be harmful to your

health. Breathing in this dust can cause allergic

reactions and/or cause respiratory illnesses for

the user or people in the near vicinity. Certain

dusts, such as oak or beech dust, are classified

as carcinogenic, especially in conjunction with

wood treatment additives (chromate, wood

preservative). We strongly advise to use a dust

extraction system that is suitable for the material

wherever possible.

Avoid dust accumulation at the

workplace. Dust can easily ignite.

The dust extraction system can be blocked by

dust, chips or fragments of the workpiece. Thus, it

must be cleaned regularly. To do so:

1. Disconnect the mains plug from the power

supply.

2. Wait until the saw blade has come to a

complete stop.

3. Remove any blockage if necessary

Mounting the dust bag

Fig. A, B

Press in the clamp of the dust bag (26) and

slide it onto the dust outlet (28) on the back of

the machine. The dust bag stays in place when

releasing the clamp.

Connecting a vacuum cleaner

Fig. A, B, T

The dust extractor must be suitable for

the material being worked.

When vacuuming dry dust that is

especially detrimental to health or

carcinogenic, use a special dust extractor.

A vacuum cleaner hose can be connected to the

dust outlet (28). To do so, simply connect the

vacuum hose to the dust extraction spout.

4. OPERATION

Before you turn on the machine, always

check that the saw blade is fitted

correctly. The blade must turn smoothly.

Always check the protective guards

before use.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm MSM1040 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info