Bedienungsanleitung Freerider FR510DXXsb (Seite 21 von 48) (Englisch)

664132

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

vehicle. Always keep your body clear of your Scooter to

prevent entrapment.

Always make certain your scooter tyres and your ramp

surface is dry, failure of observe this warning could make

your Scooter unstable and put you in a dangerous situation.

Always make certain your ramps are at a sufficiently

low angle to maintain good stability and climbing

adhesion. Failure to observe this warning could put you

in a dangerous situation.

Never ride on your Scooter when loading it into a vehicle,

failure to observe this warning could put you in dangerous

situation.

Always use a ramp with a designed load specification which

is capable of carrying your Scooter, failure to observe this

warning could put you in dangerous situation.

Always make certain that your Scooter and any ancillary

part is correctly strapped into your carrying vehicle to

prevent forward or reward movement during normal

driving or in the case of severe braking. Most of modern

vehicles have 'loading eyes' situation in the carrying

vehicles floor, use these with suitable straps to prevent

your Scooter moving.

Always make certain your scooter drive system

is in the engaged position.

For convenience, you may want to dismantle your scooter to

allow it to be transported in a smaller space. Your Scooter

can be dismantled into six individual parts (see fig 31, page

23). To enable Scoter to be dismantled and transported

follow these simple instructions. This procedure can be

carried out without tools.

1. Drive your Scooter close to the vehicle into which

you are about to load it. You may need some assistance

to life the components once your machine is dismantled.

2. Switch off your scooter. First remove the seat by releasing

the 'black' locking lever. Rotate the 90 to the right

or left , lift the seat upwards slightly twisting.This will

1. Remove your seat or fold down the backrest as necessary.

2. Lower the steering handlebars sufficiently to allow the

handlebars clearance under the top of your tail gate

entry, lock handlebars into position with black locking lever.

3. Set you 'Hi/Lo' speed switch into 'Lo' position(see fig 11

No.2, page9)

4. Set your speed 'min-max' adjustment dial (see fig11 No.1)

to a suitable power output to climb the ramp angle safely.

5. Switch Scooter 'on' and gently operate the speed control

lever, to make a slow and controlled accent of ramp.

6. When you have safety loaded your Scooter into your

vehicle switch off the power switch. Load ramp into vehicle.

To unload your scooter from your car follow points to 1

to 6 in reverse order.

Always make certain that you are on level ground when

loading and unloading your Scooter from your carrying

LOADING YOUR SCOOTER

Warning:

DISMANTLING YOUR SCOOTER

LOADING YOUR SCOOTER

Warning:

DISMANTLING

YOUR SCOOTER

FIG 21

FIG 22

FIG 23

FIG 24

FIG 25

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Freerider FR510DXXsb Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info