Bedienungsanleitung Futaba FP8SSHP (Seite 20 von 36) (Englisch)

30098

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

H. Servo reversing switches

These switches reverse the direction of the servos.

They are very convenient when connecting the linkage.

Fig.

CH8 switch

channel

CH7 lever channel

CH6 pitch control

CH5 switch channel

NORM position

: Forward

REV position

: Reverse

Rudder

Throttle

Elevator

Aileron

I. ATV/FS button

•These two pushbutton switches are used for servo

deflection angle setting of ATV, FS or HOLD func-

tion; servo test start & stop; reset; battery FS memo-

set,

etc.

•USING ATV (Aileron ATV

taken as an example)

1 First, set switch [K] [35] to the ATV side.

2 Next, set CHANNEL

SELECT switch

[J] [34]

to the

1 (aileron) position.

3 Set the transmitter and receiver power switches to

ON, and check the operation of the servos.

4 Set the aileron stick for full right rudder, hold it in

that position, and set the aileron right throw to the

desired angle by

pressing

buttons [33] and [32]

5 To set aileron left, hold the aileron stick in the full

left position and set the servo throw with buttons

[33] and [32]

(ATV can be adjusted in 64 steps. ATV can be con-

tinuously varied by pressing and holding the but-

ton for more than 1.5 seconds.)

6 For the other channels,

select

the

channel

with

the

CHANNEL SELECT switch [J] [34] and operate

ATV.

7 At the end of adjustment, set switch [K] [35] to the

center OFF position and set switch [J] [34] to OFF

position.

8 This ATV function is memorized

even if the power

switch is set to off, the ATV function

is lost if the

transistor Nicd is fully discharge.

9 When clearing the ATV, set switch [35] to RESET

and switch [34]

position 2 and

press

buttons [32]

and [33] simultaneously. ATCs of all channels are

cleared and servos deflect their 100% angle.

[32]This

pushbutton

switch

used

when:

1 Making the ATV servo deflection angle larger.

2 Turning the FS function on.

3 Starting the servo test.

—[33] This pushbutton switch is used when:

Making the ATV servo deflection angle smaller.

2 Turning the HOLD function on.

3 Stopping the servo test.

When button [32] and [33] are pressed at the same time,

reset or battery FS memory setting is possible. At this

time, lamp [A] of monitor lamps [24] goes out momen-

tarily so that setting can be monitored.

Fig.

ATV SETTING

Press button [32] and [33] while

holding the aileron stick in the

full position.

Switch switches [J] [34] and [K] [35]

HOW TO USE FS (Fail Safe)

(Throttle channel as an example.)

1 First, set switch [K] [35]

FS SELECT.

2 Set the transmitter and receiver power switches

ON, and check the movement of each servo.

3 Next, while switching the channel select switch [34]

from 1 to 8 in order, set the channels to be used

with FS, with button [32] and set the channels to

be used with HOLD, with button [33]. In this ex-

ample, set 3 (throttle) to FS with button [32].

4 Set the throttle lever to the slowest position, and

press

the FS

set

button

[36]

the

back

the

transmitter.

5 The 1 — 4 above set low throttle for the FS

function. After setting FS function, turn switch

[35] and [34]

OFF. Test

fail

safe

turning

the

transmitter power switch to OFF.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FP8SSHP Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info