Bedienungsanleitung Futaba FP8SSHP (Seite 21 von 36) (Englisch)

30098

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Each servo moves to the neutral position except

the throttle servo which moves to the slow position

that was just set.

6 Pail safe for all channels can be set with one touch

by setting the sticks and switches of the all channel

to any predetermined position

and

pressing the FS

button [36] one time.

7 The FS function can be set for all channels and any

servo deflection angle in this manner. When using

FS in all channels the function select switch must

be set to the FS ALL position.

8 Since this FS function is memorized by the trans-

mitter which transmits the data every 60 seconds,

even when the receiver power switch is set to OFF,

resetting is unnecessary.

9 After those settings, set switch [35]

OFF-to pre-

vent erroneous setting.

10 When button [36] is pressed twice, setting FS in

flight, etc., the servo position of the second is

memorized in FS and transmitted.

11 To clear the preset FS information, set switch [35]

to reset position switch [34] to position 1 and press

buttons [32] and [33] simultaneously. FS of all the

channels is cleared and all the servos move to the

neutral position.

FS function/HOLD function

The FS function is turned on with button [32] and

the

HOLD

function

turned

with

button [33]

previously described.

FS (Fail safe function)

FS is a function which moves the servo of each chan-

nel to a position preset on the transmitter when no

radio waves are received by the receiver from the

transmitter or when continuous strong noise is receiv-

ed for about one second or longer. The set operates

by the hold mode in one second and then, by the FS

mode. When the noise or interference disappears and

normal radio waves are received in approximately one

second, FS is released.

HOLD (Hold function)

HOLD is a function which stops all the servos speci-

fied by

HOLD

(by

button [33]

the

last

correct

command immediately before the erroneous signal

was received.

When the noise, interference, etc. disappears and

normal radio waves are received, HOLD is released.

Set the FS function and HOLD function as you like.

•When

switch [35]

switch

TEST-B. all

the

servos

operate linearly over their full travel. (Channel select

switch [34] in TEST-ALL position at this time.) Only

the servos set at the channel select switch are oper-

ated.

•

The

servo

test

started

by pressing

button [32]

and

stopped

pressing

button [33].

Fig.

BFS MEMORY SETTING

1 BFS (Battery fail safe function) is a function which

moves the throttle servo to a preset position as set

by the FS when there is only a small amount of

power left in the receiver Nicd battery. (If not

set, the throttle servo will be set to medium slow

automatically.)

2 The BFS setting method is the same

as the FS

usage method previously described.

3 To release the throttle servo from the preset posi-

tion

set

by BFS and

regain

control, lower the

throttle lever in the slow direction. When the

throttle lever reaches a certain point, BPS will be

released and the throttle servo can be controlled

for 36 seconds.

4 Setting this throttle lever point is called BFS

memory setting, and is done as follows:

•First, set switch [35] to BFS MEMO.SET and set

switch [34] to position [3] (throttle channel.).

• Next, while watching the movement of the servo,

set the throttle lever to the desired position (be-

tween slow and medium slow recommended) and

press buttons [32] and [33] simultaneously. This

completes BFS memory setting.

•This

memory allows

setting

the throttle to any

position, slow

high.

•Lamp

[A]

monitor

lamps [24]

goes

out

the

point where BFS is released, this allows BFS to

be checked.

•When there is little power left in the receiver

Nicd battery, the throttle servo automatically

stops at the position set by BFS, BFS is released

when the throttle lever is moved to the memoriz-

ed point. Throttle can then be controlled for 36

seconds by throttle lever

•When

the

BFS

status

comes

out

during

flight,

immediately lower the throttle lever to release

BFS. then quickly land.

•The

operation of the

servos

can

be checked by

set-

ting the transmitter and receiver power switches to

ON.

•When switch [35] is switched to TEST-A, the servos

move half-side first and then, come back to neutral

and repeat the other-half from channel 1 to channel

8. (Channel select switch [34] to TEST-ALL position

at this time.) The servos set by the channel select

switch do not operate. (If set to 5, the landing gear

servo does not operate.)

Function setting can be confirmed by means of lamp

[A] of monitor lamps

[24].

1 When switch

[35]

is at FS SELECT

When lamp [A] is on, HOLD and

when lamp

[A] is

off,

FS.

2 When switch [35] set to ALL FS, off.

3 When switch [35] set to ATV and button [32] or [33]

pressed, blink.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FP8SSHP Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info