Bedienungsanleitung Gossen Metrawatt SECULIFE ST HV (Seite 38 von 72) (Englisch)

590775

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

38 GMC-I Messtechnik GmbH

All of the possible sequence settings for all of the regulations are listed

below.

Select the Setup... menu from the initial program window and

acknowledge.

Sequence 1 (repair tests, periodic testing)

store All of the settings in the setup menu, i.e. the configu-

ration of the measuring parameters and the current

limit values can be saved with this command for the

selected test standard. These values remain active

even after setting the selector switch to a different

position, and after disconnection from mains power.

Sequence … See page 39.

Limit Values … See chapter 4.6 on page 14.

Database … Start with ID no.

x: Before each measurement is started, an entry

prompt appears requesting entry of an ID no.

An individual number can be entered (max. 20

characters) with the keypad at the (P)SI module

(optional), read in with a barcode scanner

(optional) or directly selected from a list.

If an incorrect entry is made:

Only complete lines can be deleted, and deletion

is only possible with the key at the instrument.

ID no. = test sequence (Feature KB01 or

SECULIFE ST HV

See chapter 16 on page 58.

Additional Parameters

R-PE with clip x: Protective conductor resistance can be

determined with the help of the WZ12C current clip.

High-voltage x: A high-voltage test is conducted

(prerequisite: Feature F02 or SECULIFE ST

HV)

Sequence 2 (type tests)

Type: ........ Sequences 1 and 2 differ primarily as regards the

type parameter. The user can set up any desired type

of device under test with sequence 2, for which the

same limit values and measuring parameters always

apply. Up to 125 different types can be defined. DUT

types are predefined for sequence 1 (EN 60601).

Designations made up of alphanumeric characters

(max. 10 characters) can be entered at the keypad of

a (P)SI module, or at a PC with a terminal program.

The test sequence, including all limit values, is saved

together with the selected type. We recommend

using the characters which identify the respective

standard as the initial characters in the designation. If

a type is queried from the initial program window

which does not belong to the currently selected stan-

dard, these characters identify the test sequence as

belonging to another standard.

Limit Values… See chapter 4.6 on page 14.

Sequence … See page 39.

Store as

Default All of the settings in the setup menu, i.e. the configu-

ration of the measuring parameters and the current

limit values can be saved with this command.

These values remain active even after setting the

selector switch to a different position, and after dis-

connection from mains power.

Delete The type which has been selected in the initial pro-

gram window can be deleted.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gossen Metrawatt SECULIFE ST HV Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info