Bedienungsanleitung Gossen Metrawatt SECULIFE ST HV (Seite 39 von 72) (Englisch)

590775

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

GMC-I Messtechnik GmbH 39

15.3 Configuring Measuring Parameters

Depending upon the test regulation, various measuring parameters can

be configured for the test sequence (settings: x / – = function activated /

deactivated). All of the possible parameters for all of the regulations are

listed below. The Sequence... menu is accessed via the setup parameter in

the initial program window for the respective regulation.

Select the Sequence... menu and acknowledge.

Select a parameter, acknowledge, change and acknowledge the change.

Visual inspection This menu appears at the very beginning of the test

sequence.

Manual sequence Each test step must be acknowledged with the

key (see test sequence in chapter 8 on page 18

regarding test duration for automatic sequence).

Autostore After testing is completed, test data are automatically

stored to the test instrument(Feature KB01), or in the

(P)SI module (accessory).

Mains polarity

reversal L an N are reversed each time line voltage is applied

to the test socket.

Classification Questions regarding classification appear if limit

values are exceeded, see chapter 5 on page 15.

SC III U

Supply voltage is measured instead of insulation

resistance for active devices under test.

R-INS LN-PE Insulation resistance measurement is performed

between phase and neutral conductors, and the

protective conductor.

R-INS AP-PE Insulation resistance measurement is performed from

an application part to the protective conductor.

HV test A high-voltage test is performed

(prerequisite: Feature F02 or SECULIFE ST

HV)

HV test duration Duration of a high-voltage test (5 ... 60 s)

Auto (test) method The instrument recognizes whether or not the device

under test can be switched on:

Leakage or residual current, or insulation resistance

and earth leakage current are measured accordingly.

R-PE AC > 10 A

Protective conductor measurement with 200 mA DC

10 A AC

(feature G00 or

SECULIFE ST)

oder 25 A AC

(

feature

G01 or

SECULIFE ST HV)

R-PE with clip Protective conductor resistance can be determined

with the help of the WZ12C current clip

No I

for SCI Contact current is not tested for SCI.

Mains wait A waiting period between switching mains power on

and starting the test can be entered here, e.g. in

order to suppress the display of recorded values

which occur during warm-up of the device under

test.

Patient auxiliary

current Measurement is performed with patient auxiliary

current

Adapter for socket Limit values are activated for permanently connected

devices. A device under test which is normally per-

manently installed can be connected to the test

socket via an adapter. No voltage may be applied to the

test socket when this test method is used.

First measured

values A menu for the entry of the first measured value

appears during the test sequence.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gossen Metrawatt SECULIFE ST HV Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info