Bedienungsanleitung Graupner MX-16 HoTT (Seite 42 von 200) (Englisch)

467107

Zoom out

Zoom in

Vorherige Seite

1/200

Nächste Seite

Using the transmitter for the ﬁrst time - Updating the ﬁrmware

Note:

At any time you can call up an explanation of any

step in the form of Quick-Info by positioning the

mouse pointer over a number.

If you have not already done so, connect your trans-

mitter to the PC or laptop at this point. Now click

on the button marked “File Browse” and select the

ﬁrmware update ﬁle matching your transmitter in the

“Open ﬁle” dialogue which now appears; the ﬁle suf-

ﬁx will be “bin”.

In the case of the zip ﬁle “HoTT_Software_VX”

which you have already downloaded and unpacked,

this will usually be found in the folder “Ofﬁcial Ver-

sion \ 33112_ …_ 33032_mx-xx_mc-32 \ SD card \

Firmware”, and is called “mx-16_1vXXX_German.

bin” (or “… English.bin”). The ﬁle appears in the asso-

ciated window. At the same time the “2” starts to ﬂash

red instead of the “1”.

The ﬁrmware ﬁles are encoded in a manner speci-

ﬁc to each product, i.e. if you accidentally select a ﬁle

which does not match the product (e.g. receiver up-

date ﬁle instead of transmitter update ﬁle), the pop-

up window “Product code error” appears, and you will

be unable to continue the update process.

Follow the instructions for “[Process Step] 2”. If you

have not already done so, switch the transmitter on

at this point, and then start the transmitter update by

clicking on the “Download Start” button.

Shortly after this you will see a warning that the

transmitter’s RF signal is being disabled: “RF will be

switched OFF.” Before clicking on “Yes” you should

therefore switch the receiving system off if it is cur-

rently operating.

At this point the actual update process begins, and a

progress bar starts to advance above the constantly

changing lines of text. At the same time the ﬂashing

red number continues to indicate the current “Proc-

ess Step”.

You must not interrupt the connection between

the transmitter and the PC during the update

process!

The update is ﬁnished when the progress bar reach-

es the right-hand end, and the message “Firmware

Download Success” appears. At the same time the

[Process Steps] display moves on to “7” “Update

Process Finish”:

Click on “OK”, then switch the transmitter off and ﬁ-

nally disconnect the lead between the transmitter and

the PC or laptop.

If the progress bar fails to advance, or if the update

process terminates before it reaches the 100% mark,

close the program and repeat the update procedure,

i.e. carry out each of the steps described above once

more. If an update fails repeatedly, please read the

following section.

If you accidentally attempt to load a version of the

ﬁrmware which is correct, but older than the one cur-

rently in the transmitter, the screen will display a cor-

responding warning:

Unless you really want to load older ﬁrmware, click

on “No” with the mouse, and load the correct *.bin ﬁle

using the “File Browse” button.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner MX-16 HoTT Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Graupner MX-16 HoTT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info