Bedienungsanleitung Graupner MX-16 HoTT (Seite 43 von 200) (Englisch)

467107

Zoom out

Zoom in

Vorherige Seite

1/200

Nächste Seite

Using the transmitter for the ﬁrst time - Updating the ﬁrmware

Restoring the transmitter’s ﬁrmware

„Emergency“ program

Restoring the mx-16 HoTT transmitter software

If a transmitter ﬁrmware update should fail, or if the

transmitter software “hangs” (in which case you may not

be able to switch the transmitter off using the “POWER”

switch), then you can restore the earlier ﬁrmware using

the “Emergency” program segment.

If you switch the transmitter off, but the screen con-

tinues to be active, then please set the switch to the

“POWER=OFF” position, unplug the transmitter battery,

wait a few seconds, then plug it in again - but leave the

POWER switch at the “OFF” position!

Starting the “Emergency” program1.

Now move to the “Controller Menu” and select the

“Emergency” entry under the heading “Transmitter”:

Ensure that the transmitter is switched off! Connect

the USB lead to the PC or laptop, and to the USB

socket on the back of the transmitter.

Restoring the 2. mx-16 transmitter software

Press the “File Browse” button and search for the

current ﬁrmware in the program window which now

opens; as mentioned earlier, you will ﬁnd this in the

“Ofﬁcial Version \ 33112_…_33032_mx-xx_mc-32 \

SD card \ Firmware” folder of the unpacked “HoTT_

Software_VX” ﬁle. The ﬁle matching the mx-16

transmitter is called: “mx-16_1vXXX_German.bin” (or

“…English.bin”).

Now press the “Download Start” button to initiate the

update process. Wait for a moment until the status

bar starts to advance, and only then switch the trans-

mitter on. Don’t be surprised if the screen comes to

life, but displays no information.

(If the progress bar reaches the right-hand end be-

fore the transmitter is switched on, you will have to

click on the “Download Start” button again.)

After you switch the transmitter on, there may well

be a wait lasting a minute before the process actual-

ly starts.

The progress bar indicates that the data transfer

process is under way, and the screen displays [Proc-

ess Step] “No 4, Firmware downloading …”.

Ensure that the USB lead is making reliable contact,

and do not interrupt the update process.

The ﬁrmware transfer is ﬁnished when the progress

bar reaches the right-hand end; you will then see the

message “File Transfer Success” to indicate that the

transfer has been successful.

The transmitter’s signal melody sounds, the trans-

mitter screen switches itself on with the start display

“mx-16 HoTT”, and the current ﬁrmware version is

shown on the screen.

Finally click on “OK”. Switch the transmitter off, and

disconnect the USB lead from the transmitter and the

PC or laptop.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner MX-16 HoTT Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Graupner MX-16 HoTT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info