Bedienungsanleitung Graupner MX-16 HoTT (Seite 44 von 200) (Englisch)

467107

Zoom out

Zoom in

Vorherige Seite

1/200

Nächste Seite

Using the receiver for the ﬁrst time

Preliminary notes regarding the GR-16 receiver

For more information please visit the Internet at www.graupner.de.

Receiving system

The mx-16 HoTT radio control set includes a GR-16

2.4 GHz bi-directional receiver which is suitable for con-

nection to a maximum of eight servos.

If you switch a HoTT receiver on, and “its” transmitter

is switched off or not within range, the red LED on the

receiver lights up steadily for about one second, and

then starts to ﬂash slowly. This means that no connec-

tion with a Graupner|SJ HoTT transmitter exists (at this

stage). When the connection is made, the green LED

glows constantly, and the red LED goes out.

In order to create a connection, the Graupner|SJ HoTT

receiver must ﬁrst be “bound” to “its” model memory in

“its” Graupner|SJ HoTT transmitter; this procedure is

known as “binding”. However, binding is only necessary

once for each receiver / model memory combination

(see pages 80 or 88), and has been carried out at the

factory for model memory 1 using the components sup-

plied in the set. You therefore only need to carry out the

“binding” process - as described later - with additional

receivers, or if you switch to a different model memory.

The procedure can also be repeated whenever you wish

- for instance, if you change the transmitter.

Receiver voltage display

Once a telemetry connection exists, the actual voltage

of the receiver power supply is displayed on the right-

hand side of the transmitter screen.

Temperature warning

If the temperature of the receiver falls below a limit value

set on the receiver (the default is -10°C), or exceeds

the upper warning threshold, which is also set on the

receiver (the default is +55°C), the transmitter generates

a warning in the form of steady beeps at intervals of

about one second.

Servo connections and polarity

The servo sockets of Graupner|SJ HoTT receivers are

numbered. The connector system is polarised: look for

the small chamfers when inserting the connectors, and

on no account force the plugs into the sockets.

The sockets marked “1+B-” and “6+B-” are intended

for the connection of the battery. It is also possible to

connect the appropriate servos to both these sockets in

parallel with the power supply by using a Y-lead, Order

No. 3936.11.

Do not connect the battery to these sockets with

reversed polarity, as this is likely to ruin the receiver

and any devices connected to it.

The power supply voltage is through-connected via all

the numbered sockets. The function of each individual

channel is determined by the transmitter you are using,

rather than by the receiver. Example: the throttle servo

socket is deﬁned by the radio control system, and may

differ according to the make and type.

In the case of Graupner radio control systems the

throttle function is assigned to channels 1 or 6, whereas

it is allocated to channel 3 in the case of Futaba radio

control systems, for example.

Observe the installation notes regarding the receiver, re-

ceiver aerial and servos, which you will ﬁnd on page 52.

Concluding notes:

The much higher servo resolution of the HoTT sys-•

tem results in a substantially more direct response

compared with previous technologies. Please take a

little time to become accustomed to the ﬁner control

characteristics offered by the system!

If you wish to use a speed controller with integral •

BEC* system in parallel with a separate receiver bat-

tery, in most cases (depending on the speed control-

ler) the positive terminal (red wire) must be removed

from the three-pin connector, as shown in the dia-

gram. Be sure to read the appropriate notes in the in-

structions supplied with your speed controller before

doing this.

Carefully raise the central lug of the connector slight-

ly (1), withdraw the red

wire (2) and insulate the

bare contact with tape

to avoid possible short

circuits (3).

red

Reset

To carry out a receiver reset, locate the SET button on

the top of the receiver and hold it pressed in while you

switch the receiver power supply on. Hold the receiver’s

SET button pressed in until the green and the red LED

goes out; this takes about four seconds.

If you carried out the reset with the transmitter switched

off, or with an unbound receiver, the receiver LED will

ﬂash red slowly after a pause lasing about two seconds.

At this point it is immediately possible to initiate a Bind

process at the transmitter.

If the reset is carried out with an already bound receiver,

if the transmitter is switched on, and if the associated

model memory is active, then the LED lights up green

after a short interval to indicate that your transmitter /

receiving system is ready for use once more.

* Battery Elimination Circuit

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner MX-16 HoTT Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Graupner MX-16 HoTT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info