Bedienungsanleitung Jablotron JA-80K (Seite 6 von 22) (Englisch)

554835

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

Installation manual: Oasis security system JA-80K - 6 - MKE51801

disconnected. After the mains supply has been restored battery

charging starts again and the system will begin to function again.

Ensure that the battery is correctly connected (Polarity: RED =

positive +, BLACK = negative -).

WARNING – the battery is sold charged – to maintain safety, avoid shorting

out the terminals !!!

7. Powering-up the control panel for the first

time

• First check all the wiring, and if a GSM communicator is

installed, insert its SIM card (PIN code disabled).

• Carefully connect the back-up battery,

• Carefully connect up the mains. A green LED will start

flashing on the control panel board.

• If a hard-wired keyboard is connected it will indicate Service

mode. If not, the control panel is not set to the factory default

and should be reset (see section 9.).

7.1. Wireless keypad enrollment

If no hard-wired keypad is connected to the control panel, and

the wireless keypad was not supplied as part of a JK kit, the

wireless keypad must be enrolled to the control panel as follows:

1. Have an opened keypad and its battery ready.

2. Check that the green LED in the control panel is flashing.

3. Short the reset link in the control panel for 1 second (e.g.

using a screwdriver). This will enter enrollment mode on

the control panel.

4. Install batteries into the keypad not far from the control

panel.

5. The keypad generates a beep sound and enrolls to

address. After that it indicates “Enrollment 04: Device”.

6. Press the # key to exit enrollment mode and “Service”

will be indicated on the keypad.

Warning:

• If the keypad does not enroll, then the control panel settings

are not the factory-defaults. In this case perform a reset and

repeat the enrollment procedure.

• If you want to assign the keypad to another address, re-

enter enrollment mode via the “1” key, then use the arrow

keys to select the desired address. Then disconnect the

keypad battery and reconnect it.

Recommendation: it is highly recommended to install the

wireless keypad with a magnetic door sensor wired to its hard-

wired input terminal. This way the keypad will wake up every

time after opening the door and it will produce entrance delay

beeps and will be ready to read access cards. It will also save

money on a wireless door detector.

8. Language selection of the keypad

If the ∗ key is kept pressed during battery connection, the internal

keypad menu will be displayed allowing the selection of the desired

language. Using the arrows, choose your language and confirm

selection by the ∗ key.

In this menu the door bell function can also be enabled or

disabled (if enabled the keypad makes a sound when its IN input

is triggered).

Notes:

• for the JA-80E wired keypad the power can be connected

by connecting its cable or by turning on the control panel

power

• if the wireless keypad has already had its battery

connected, it is necessary to disconnect the battery for a

while before pressing and holding the ∗ key

• the language can be selected for each individual keypad in

the system (i.e. different keypads can display different

languages – for example if foreigners are working in the

company)

9. Resetting the control panel

If you need to return the control panel to the factory-default

settings perform the following:

1. Disconnect the back-up battery and the mains (for

example by removing the fuse from its terminals).

2. Connect the RESET link and leave it connected.

3. Connect the back-up battery and the mains

4. Wait till the green LED starts flashing and then

disconnect the RESET link

Warning:

• After a RESET, all wireless devices are erased from the

control panel and all user codes and access cards are

“forgotten”.

• After a RESET, the Master code returns to 1234, and the

service code to 8080.

• If resetting is disabled (see 12.9) it is impossible to reset the

control panel.

10. Closing the control panel cover

After the keypad has started working it is possible to close the

control panel cover. Before this is done, check that the control

panel has an antenna connected.

11. Enrolling wireless devices

The control panel has 50 addresses (01 to 50), allowing the

enrollment of up to 50 wireless devices i.e. detectors, keypads,

keyfobs, sirens, etc. A wireless device can be assigned to an

address by enrollment or by entering its production code (see

12.42).

11.1. Installing wireless devices

Wireless devices can either be installed at their desired

locations first and then enrolled to the control panel or vice

versa. If there any doubts as to the suitability of device locations

for radio communication, temporarily attach the devices (e.g.

using adhesive tape) and test radio communication before

finalizing installation. Follow the manuals of the particular

devices during their installation.

11.2. Enrolling wireless devices to the control panel

1. The control panel should be in Service mode. If it is not,

then enter ∗0 service code (factory default: 8080). The

control panel must be unset (disarmed).

2. Press the “1” key, enrollment mode will be entered and the

first vacant address will be offered. For a new control panel

it will be 03.

3. Using the arrows keys

and , you may select the

desired address. If the address is already occupied this is

indicated by the A indicator being lit.

4. The device will enroll to the selected address just after its

battery (power) is connected .

5. Enrollment is confirmed by the A indicator and the next

vacant address is then offered.

6. By connecting batteries to all devices one after the other

they will all be enrolled to the control panel. Press the # key

to exit enrollment mode.

teké

Notes:

• If a wireless device is enrolled to address 01 or 02 this will

disable the corresponding hard-wired input terminal (if a

wireless device is erased from address 01 or 02, the hard-

wired terminal will be re-enabled).

• Keyfobs type RC-8x can be enrolled by pressing and holding

a pair of buttons simultaneously, i.e.:

+ or +

(enrollment by battery installation will enroll buttons

+ ).

This means that a 4-button keyfob can be enrolled to the

Jablotron JA-80K Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron JA-80K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info