Bedienungsanleitung Korg microKORG S (Seite 56 von 73) (Englisch)

707422

Zoom out

Zoom in

Vorherige Seite

1/73

Nächste Seite

Messages transmitted and received by the microKORG S

If you want program changes to be transmitted and received, set the SHIFT function

"MIDI FILTER" to PROGRAM CHANGE Enable (

). If this is set to Disable ( ),

program change messages will not be transmitted or received.

❏

Pitch bend

Pitch bend change [En, bb, mm]

(n: channel, bb: lower digits of value, mm: upper digits of value)

When pitch bend change messages are received, a pitch bend will occur according to

the PITCH "BEND RANGE" value. Pitch bend can also be used in a Virtual Patch for a

synth program, or as an FC MOD modulation source for a vocoder program. In this

case, the message will act as a modulation source where mm=64, bb=00 will be 0

(center value) for the range of -127 - +127. (This message is received on the timbre

channel.)

When you move the PITCH wheel on the microKORG S, pitch bend change messages

are transmitted on the MIDI channel("MIDI CH").

If you want pitch bend changes to be transmitted and received, set the SHIFT function

"MIDI FILTER" to PITCH BEND Enable (

). If this is set to Disable ( ), pitch

bend change messages will not be transmitted or received.

❏

Control changes

Control changes [Bn, cc, vv]

(n: channel, cc: control change no., vv: value)

When you use knobs 1–5 to edit certain parameters, or when you operate certain keys

or the MOD wheel, the assigned control change will be transmitted. Conversely, when

control change numbers corresponding to the knob 1–5 settings are received, the

corresponding controller or parameter will be controlled.

❏

MIDI channels

MIDI uses sixteen channels (1-16). MIDI messages can be transmitted and received

when the channel of the receiving device matches the channel of the transmitting

device.

MIDI messages such as note-on/off and pitch bend are transmitted and received on

the MIDI channel specified by the MIDI "MIDI CH" setting.

❏

Note-on/off

Note-on [9n, kk, vv], Note-off [8n, kk, vv]

(n: channel, kk: note number, vv: velocity)

When you play the keyboard of the microKORG S, note-on/off messages are

transmitted.The note-off velocity is transmitted at a fixed 64, but is not received.

If the MIDI "POSITION" is Post KBD (

), note-on/off messages will be transmitted

by the arpeggiator when it is running.

❏

Program change

Program change [Cn, pp]

(n: channel, pp: program number)

Bank Select (CC#00) [Bn, 00, mm]

Bank Select (CC#32) [Bn, 20, bb]

(n: channel, mm: bank number upper byte, bb: bank number lower byte)

When you switch the program on the microKORG S, bank select and program change

messages corresponding to the selected program number 1 - 256 (A.11 - d.88) will be

transmitted. Similarly, when the microKORG S receives bank select and program

change messages, the program will change. (➝Voice Name List)

Middle C on a

piano is C4 (MIDI

note number 60)

Octave Shift settings and note numbers

(96)

(108)

(120)

(127)

C#8

(116)

(120)

(72)

(84)

(48)

(60)

(24)

(36)

C-1

(0)

(12)

Octave Shift not used

+1 octave

+2 octaves

+3 octaves

-3 octaves

-2 octaves

-1 octave

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg microKORG S Seite 56

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Korg microKORG S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info