Bedienungsanleitung Korg microKORG S (Seite 57 von 73) (Englisch)

707422

Zoom out

Zoom in

Vorherige Seite

1/73

Nächste Seite

If you want control changes to be transmitted and received, set the SHIFT function

"MIDI FILTER" to CONTROL CHANGE Enable (

). If this is set to Disable ( ),

control change messages will not be transmitted or received.

• Modulation depth (CC#01) [Bn, 01, vv]

When a modulation depth message is received, the LFO2 vibrato depth will change

according to the value specified for PITCH "VIBRATO INT." If the value of the

received message is the maximum value (127), vibrato will be applied over the full

pitch range specified by "VIBRATO INT." If the value of the received message is 0, no

vibrato will apply.

When you move the microKORG S's MOD wheel, modulation depth messages are

transmitted on the MIDI channel ("MIDI CH").

•Volume (CC#07) [Bn, 07, vv]

If you assign control change (CC#07 – volume) to AMP "LEVEL," volume messages

can be received to control the volume.

•Panpot (CC#10) [Bn, 0A, vv]

If you assign control change (CC#10 – pan) to AMP "PANPOT," pan messages can be

received to control the stereo position of the sound.

Assigning control changes to knobs and keys

You can use the SHIFT function "CONTROL CHANGE" to assign a control change in the

range of CC#00–CC#95 to principal parameters that correspond to panel knobs and

keys. When you operate the assigned knob or key, the corresponding control change will

be transmitted. If the Performance Edit function is enabled, the control change for the

corresponding parameter will be transmitted.

When control changes are received from an external device, the microKORG S will

behave according to the value of the control change, just as when the corresponding

knob or key is operated (➝p.56 "Control change assignments for the microKORG S's

knobs and keys"). In addition, when you use the front panel TIMBRE SELECT key to

switch timbres, a message (Timbre Select) indicating which timbre is selected will be

transmitted. When the microKORG S receives a Timbre Select message, it will switch

timbres according to the value of the message. (0: Timbre 1, 1: Timbre 1&2 (Sync), 2–127:

Timbre 2).

You can use the SHIFT function "CONTROL CHANGE" Timbre Select to assign a control

change to Timbre Select as well.

Sync control

The first-played note-on will sync a LFO whose "KEY SYNC" = Timbre( ).

However in order to distinguish manually played note-on/off's from those that are

repeated automatically by the arpeggiator, the microKORG S's arpeggiator will

transmit a Sync Control message at the time of note-on (when MIDI "POSITION" is

Post KBD(

)).

A control change message is used for this Sync Control message as specified by Shift

function "Control Change."

By using Sync Control to apply sync to a LFO, you can cause each arpeggiated note to

advance the random LFO by one step.

Silencing all notes of a given channel

• All note off (CC#123) [Bn, 7B, 00] (value is 00)

When an All Note Off message is received, all currently-sounding notes of that

channel will be turned off. Some sound may linger due to the envelope settings.

• All sound off (CC#120) [Bn, 78, 00] (value is 00)

When an All Sound Off message is received, all notes currently sounding on that

channel will be silenced. While All Note Off allows the decay of a note to continue, the

All Sound Off will silence the sound immediately.

However, this message is intended for use in emergencies, and is not for use during a

performance.

Resetting all controllers of a given channel

• Reset all controllers (CC#121) [Bn, 79, 00] (value is 00)

When a Reset All Controllers message is received, all controller values currently

operating on that channel will be reset. Some parameters assigned using Virtual Patch

will not be reset.

❏

Parameters transmitted and received via NRPN

Front panel knobs and keys other than the controls listed above are assigned NRPN

(Non Registered Parameter No.). NRPN messages can be used freely by any musical

instrument manufacturer or model.

NRPN editing is performed using the following procedure.

Use NRPN MSB (CC#99) [Bn, 63, mm] and NRPN LSB (CC#98) [Bn, 62, rr] (n:

channel, mm, rr: parameter no. upper and lower bytes) to select the parameter.

Use data entry MSB (CC#6) [Bn, 06, mm] (n: channel, mm: parameter value) to specify

the value.

On the microKORG S, only data entry MSB is used.

Controlling the arpeggiator

When arpeggiator settings are modified by the front panel keys or knobs, the following

NRPN messages are transmitted. When these NRPN messages are received, the corre-

sponding arpeggiator settings will change accordingly. These messages are transmitted

and received on the MIDI channel(“MIDI CH”). For the correspondence between the

values of the message and the values of the microKORG S parameter, refer to the table.

Messages transmitted and received by the microKORG S

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg microKORG S Seite 57

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Korg microKORG S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info