4
Indoor relative
humidity %
button
Indoor relative
humidity %
1. Hold the body of the pool sensor and unlock the upper part by
turning it counter clockwise and
body.
2. Insert batteries observing the correct polarity (see marking).
3. Screw the two parts together again.
flat and sufficiently tight secured (markings
correspond). This will prevent water from entering the batter
compartment and subsequently damage the unit.
HOW TO INS
TEMPERATURE S
The temperature station u
AAA, IEC LR3, 1.5V batteries. To
install and replace the batteries,
please follow the steps below:
1. Open the battery compartment
by pushing the battery cover
upwards with your thumb.
Insert batteries observing the
correct polarity (see marking).
2. Replace compartment cover.
SETTING UP
1. First, insert the batteries in the outdoor transmitTo
install and replace batteries
transmitter” above).
2. Then, insert the batteries in the pool sensor (see “To install
and replace batteries in the pool” above)
3. Within 15 seconds of powering up the outdoor transmitter and
pool sensor, insert the batteries in the temperature station
(see “To install and replace batteries in the temp
station” above). Once the batteries are in place, all segments
of the LCD will light up briefly. Following
temperature/humidity and the time as 00:00 will b
If this information is not displayed on the LCD after
seconds, remove the batteries and wait f
seconds before reinserting them. Once the indoor data is
displayed user may proceed to the next step.
4. After the batteries are inserted, the temperature stati
start receiving data signal from the outdoor
pool sensor. The outdoor temperature data
displayed on the temperature station. If this does not
after 5 minutes, the batteries will need to be removed fro
units and reset from step 1.
5. In order to ensure sufficient 868 MHz transmission
the distance between the temperature station and the outdoor
transmitter should not be more than 100 meters an
meters to the pool sensor (in water). (see notes on
“Positioning ” and “868 MHz Receptio ”).
Note:
In the event of changing batteries of the units, ensur
batteries do not spring free from the contacts. Always wait at
least 1 minute after removing the batteries
otherwise start up and transmission problems may occur.
6. Once the outdoor data reception period is completed, the D
tower icon in the clock display will start fl
left corner. This indicates that the clock has detected
there is a radio signal present and is trying to receive it. W
the time code is received, the DCF t
permanently lit and the time will be displayed.
RADIO-CON
The time base for the radio controlled time is a Cesi
operated by the Physikalisch Techni
Braunschweig. It has a time deviation of les
million years. The time is coded and transmitted from Mainflingen
near Frankfurt via frequency signal DCF-77 (77.5 kHz) and has a
transmitting range of approximately 1,500 km. Your radio-controlled
clock receives this signal and converts it to show the preci
‘Changeover from summer time or winter time is automatically.
The quality of the reception depends greatly on the g
location. In normal cases, there should b
within a 1.500 km radius of Frankfurt.
DCF reception is done twice daily at
reception is not successful at 03:00 am, then the next reception takes
place the next hour and so on until 06:00am, or un
successful. If the reception is not successful
next attempt will take place the next day at 0
Please take note of the following:
The recommended distance to any interfering sources like
computer monitors or TV sets is a minimum of 1.5 -
Within Ferro-concrete rooms (basements, superstructures),
the received signal is naturally weakened.
please place the unit close to a
or back towards the Frankfurt transmitter.
During nighttime, the atmospheric disturbances are usually
less severe and reception is possible in most cases. A single
daily reception is adequate to keep the accuracy deviation
under 1 second.
FUNCTION BUT
Temperature station
The device has 3 easy to use function butt
and 2 buttons on the back
LCD SCREEN
The LCD screen is split into 4 sections displaying the inf
time, indoor temperature and hu
temperature.
* When the signal is successfully received by the temperature
station, the outdoor reception icon will
successful, the icon will not be
easily see whether the last reception was successful (icon on) or not
(icon off). On the other hand, the
a reception is currently taking place.
MANUAL SET
Time zone setting
Time reception ON/OFF setting
12/24-hour setting
Manual time setting
°C/°F temperature setting
Factory reset setting (FAC)
Press and hold the SET button for ab
setting mode:
TIME ZONE S
The time zone default is 0h. T
1. The value of the actual set time zone will be flashi
2. Using the + button, set the time zone. The
2h to +5h in consecutive 1 hour inter
3. Confirm with the SET button and enter the “Time receptio
ON/OFF setting”.
TIME RECEPTI
In areas where no DCF-77 time is possible,
possibility to deactivate the DCF reception manually (OFF)
clock will then work as a normal quartz clock. (Defa
1. The symbol “ON” will be flashing on the
2. Use the + button to deactivate (OFF) the time recep
function.
3. Confirm with the SET button and enter the “12/24-Ho
Display setting”.
Note:
If the time reception f
clock will not attempt any receptio
(DCF time) as long as the time rec
activated (ON) again. If the time reception is dea
the DCF symbol disappears.
12/24 HOUR TIM
1. “24h” will be flashing.
2. Press the + button to select the “12h” or
3. Confirm with the SET button and to enter tM
setting”.
MANUAL TIME S
In case the device is not able to attempt the r
(disturbances, transmitting distance, etc.), the ti
set. The clock will then work as a normal quartz cl
To set the clock:
1. The hour digits will be flashing on the display.
2. Use the + button to adjust the hours.
3. Press the SET button to go to t
4. Use the + button to adjust the minutes. Press and hold the
button in the setting mode for fast r
5. Confirm with the SET button and enter the “ºC/ºF temp
unit setting”.
Note:
By a successfully reception of the DCF si
reception is activated (ON), the manually set
During the reception the DCF symbol will be flashing. If the reception
is not successful received, the DCF symbol disappear
attempt will still be held.
°C/°F TEMPER
The default temperature is
(degree Fahrenheit):
1. During “ºC” will be flashing, use the + button to toggl
“ºC” and “ºF”.
2. Once the desired temperature unit has been chosen, confirm
with the SET button and enter the “Factory sett ” or press
the MAX/MIN / RESET button to e
FACTORY RESE
To reset the temperature station to t
1. Press and hold the + button for about 3 seconds to reset the
manual settings to factory settings.
2. Once the factory setting is done, all segments of the L
light up briefly, then the time, indoor temperature and humidity
will be displayed.
Important:
During factory setting, all signals from the transmitters are los
order to receive the transmission signals from the tr
please refer to “Setting ” above to set the initial reception signal
again.
TO EXIT THE M
To exit the manual setting mode anytime during the manual
press the MAX/MIN / RESET button.
OUTDOOR TR
SEARCH M
If the transmitters are lost due to di
transmitting distance, etc., a manual tran
started.
1. Press the + button to select the
2. “LEARN” appears in the display of the selected trans
3. Press the SET button to start the sear
4. The reception symbol will be flashing.
5. As soon as the transmitter is found, the temperature appears
and the reception symbol stays in the display.
INDOOR TEMPE
DATA
The indoor temperature and humidity are d
displayed on the second section of the LCD.
To display the dew point temperature,
button 3 times.
DEW POINT appears in the display.
The device will automatically quit the dew point mode if no
pressed for a lengthy period (30 seconds) or press the MAX/MIN /
RESET button again to return
Note: The dew point value is bas
temperature and humidity data.
in °C/°F
Minutes
(flashing)
Flashing
Flashing
Flashing
Flashing
SET button
Time
humidity %
Outdoor reception signal (p
°C or °F
reception)
Low battery
indicator
station)
Low battery
indicator (pool
sensor)
Low battery
indicator
(temperature
transmitter)
Outdoor
reception
signal
(transmitter)*
Time Zone (flashing)
Reception
signal flashing
