Bedienungsanleitung Messner Mini-Versailles (Seite 6 von 13) (Deutsch, Englisch, Französisch)

609960

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

8 9

Repair work

Read the safety guidlines thoroughly before servicing or repairing the appliance!

Opening of the water display

Take off all jets and turn the water display upside down (jet connections downwards).

Turn the 9 screws with hexagonal recessed holes on the outside and the hexagon cap screw in the middle

out of the base plate of the water display.

Thereby it is possible to do all repair work.

Failure of a water pattern or permanent running of one water pattern:

Phase 1: one Volcano Jet 3-tiered (center)

Phase 2: three Calyx Jets VARIO

Phase 3: three Volcano Jets 2-tiered

Phase 4: three Bell Jets

Mechanical load and natural wear and tear may result in a failure of the component parts of the drive/

distributor.

Please proceed as follows:

1. Open the water display

(as described before)

2. Loosen the eight screws on the

distributor cover of the drive and

remove the cover.

3. From the drawing you can learn

which distribution or which

center connection runs to the

jet failed. Draw this element out

of its conductor and check whether:

a) the stainless steel spring,

ﬂ ap or holder are broken

b) the ﬂ ap closes

automatically

c) the closed ﬂ ap ﬁ ts snugly;

do compare with the other

ﬂ aps

4. If there is a damage, we

recommend to replace

the complete set,

3 x distribution and

1 x center connection.

Lighting

In case the lighting has failed, maybe the halogen incandescent lamp in the ﬂ oodlight has exceeded its

service life.

Loosen the two tapping screws beside the defective ﬂ oodlight and pull it out of the appliance together with

the holding ring. By bending up the three hooks, separate the ﬂ oodlight from the holding ring.

Changing of the lamp

Attention! As a replacement, one may use (nearly) all commercial cool-beam, reflectable lamps,

max. 20 watts.

1. Pull out mains plug and secure against reclosing.

2. Hold tight the ﬂ oodlight casing and unscrew the ﬂ oodlight ring anticlockwise.

3. Remove the ﬂ oodlight glass.

4. Remove the lamp from the casing and remove the ceramic socket.

5. Before re-assembling the ﬂ oodlight, please clean the glass and the sealing ring.

Do avoid using scouring liquids or any sharp instruments.

The sealing ring is ﬁ tted to the casing and should not be removed.

6. Replace the lamp, put it again in the socket and re-insert it into the casing.

7. Place the glass on the sealing ring which is provided on the casing, put back the ﬂ oodlight ring and screw

it clockwise.

For re-assembling the complete ﬂ oodlight on the appliance, clip the holding ring again to the ﬂ oodlight,

re-insert both pieces into the “Versailles” and tighten with the 2 tapping screws.

Taking care of your waterworks in winter

Protect the waterworks against frost.

Take the appliance out of the water in autumn and store it in a frost-proof room during the winter months.

Guarantee conditions

This Water Display «Versailles mini» comes with a 24-month guarantee (ﬂ oodlight lamp excluded) that

is effective from the date of delivery. The invoice will be the proof of the date. In case of damages due to

defects in material or manufacturing, we shall either do a free repair during the guarantee period or replace

the damaged part, the choice being ours’.

Damages that occur due to installation and operating errors, lime deposits, insufﬁ cient care, frost action,

normal wear and tear or improper repair attempts will not come under this guarantee. The guarantee will not

be valid in case of modiﬁ cations to the apparat, e.g. cutting off the line connection or the line cord. We will

not accept responsibility for consequential damages resulting from breakdown of the apparat or improper

operation.

When making use of the guarantee, please send us the apparat, along with the corresponding invoice, free

of charge via the specialist dealer who sold you the apparat.

Drive/distributor

sectional view

Distributor cover

Flap and spring

Sectional view without gear

Distribution, Bell Jets

Distribution,

Calyx Jets VARIO

towards pump

Distribution,

Volcano Jets,

2-tiered

Center connection,

Volcano Jet, 3-tiered

Drive/distributor

top view

Floodlight ring

Glass

Lamp

Socket

Sealing ring

Floodlight casing

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Messner Mini-Versailles Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info