Bedienungsanleitung Multiplex PROFIcar4000 (Seite 5 von 16) (Englisch)

30242

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

PROFI mc 4000PROFI mc 4000

Version 2.0

3. Logic-coupled switches

The logical switches fulfil a wish which we have heard

from many modellers:

„I want my airbrakes to be locked unless and until I

select the ‘landing’ flight mode AND the throttle is be-

low 20%“; or

„I want the on-board glow system for my motor to be

switched on when I operate a switch, OR when the

throttle is below 20%, OR when I operate the on-

board starter.“

These are two good examples of applications for

logic-coupled switches.

The new software allows you to define four such

switches: LOG1 to LOG4, and each of the four

switches can have up to four inputs. The linking pos-

sibilities are AND and OR.

AND linking means:

2, 3 or 4 4 conditions must be fulfilled simulta-

neously if an effect is to take place.

Example:

The airbrakes can only be extended if you have

selected the ‘landing’ flight mode (e.g. using the

transfer switch T1-1) AND the throttle is below

1/4 (e.g. with control switch C4-D).

OR linking means:

At least one condition must be fulfilled before

an effect can take place.

Example:

The „on-board glow system“ is to be switched

on when the throttle signal is below 20% (e.g.

with control switch C-D),

OR when you operate switch S06,

OR automatically when the on-board starter is

operated.

This is how it’s done:

To implement the first example (airbrakes) you use

the following procedure:

1. Servo 12 controls the airbrakes.

Assign the servo:

SERVO 12 is SERVOMIX

Assign Mixer for Servo 12:SERVOMIX

input: FIXED VALUE (-100% = brake closed)

input: FIXED VALUE (+100% = brake open)

2. Define transmitter control switch

Assign switches

CONTROL SW: C4 Ä

;FROM CONTROL D

,1-POINT: MAX - 50%_

We set the control switch to -50%, as we assume

that –100% is idle and +100% is full throttle.

3. Defining logic-coupled switches

Assign switches

LOGICAL SW:LOG1 Ä

;INPUT 1

,AND C4-D#*_

You now have to press the w button to open the field

for the control switch and then reverse the control

switch with the R button. This is necessary because

the control switches normally switch ON when the

signal exceeds the switching threshold (MAX). How-

ever, in our example the airbrakes are required NOT

to extend if the throttle is open more than ¼ of full

travel.

The second input to the logic-coupled switch is the

transfer switch T1-1, which simultaneously acti-

vates the ‘landing’ flight mode.

Assign switches

LOGICAL SW:LOG1 Ä

;INPUT 2

,AND W1-1'*_

In this case no reversing is required.

4. The first step here is to assign SERVOMIX to each

airbrake servo (Menu 2: Assigning/SERVOS).

In Menu 2 „Assigning MIXERS“ we assign FIXED

VALUE to input 1 and input 2. This has to be

done separately for the SERVOMIXers of all the

airbrake servos in your model. The two fixed

values correspond to the airbrake settings „ex-

tended“ and „retracted“.

'' TIP:

When assigning the inputs for Servomix you will find

FIXED VALUE directly after „AUX. 4“.

In the menu point TRAVEL/CURVE, under MENU

1: SERVO adjustments, you can now set the fixed

value and assign the switches. You select the

same logic-coupled switch (e.g. L1) for both fixed

values. However, note that you have to reverse

the effect of the switch for input 2 by pressing the

y button.

This ensures that one of the two inputs is always

switched on and the other switched off.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex PROFIcar4000 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info