Bedienungsanleitung Multiplex ROYALevo12 (Seite 40 von 57) (Englisch)

30266

Zoom out

Zoom in

Vorherige Seite

1/57

Nächste Seite

Instructions

Page 95

14.2.2. Parameter „Trim“

N display only

change using cruciform trim buttons

4 one trim value for each flight phase

The value of this parameter indicates the extent of the

trim for this control, i.e. the magnitude and direction of

the trim correction. It is calculated from the increment

size TStep and the number of trim steps used. If the

largest increment size (3.5%) is selected, the trim travel

can be up to 70% in each direction.

14.2.3. Parameter „Step“ (trim increment)

0,5% – 1,5% – 2,5% – 3,5%

Only these four values can be selected for the trim step.

The number of trim steps is +/- 20, giving trim range

values of +/- 10%, +/- 30%, +/- 50% and +/- 70% respec-

tively

14.2.4. Parameter „D/R“ (Dual-Rates)

F can be assigned to a 3-D digi-adjustor

10% to 100%

Dual Rates enable the user to change the control sensi-

tivity of the model. For example, if the Dual Rate pa-

rameter is set to 50%, you can reduce the model’s con-

trol surface travels to half of normal by operating the

assigned switch.

14.2.5. Parameter „Trvl“

This parameter is used to determine the percentage of

full servo travel which can be obtained using the associ-

ated transmitter control.

14.2.6. Parameter „Expo“

F can be assigned to a 3-D digi-adjustor

-100% to 100%, 0% = OFF

This parameter allows you to assign an exponential

characteristic to the transmitter control. If Expo is 0%,

the transmitter control is linear in effect. Negative Expo

values have the effect that control in the area around

the centre position produces reduced control surface

travels, giving you fine control around neutral. Positive

Expo values have the opposite effect: the control sur-

face travels are greater around the centre position.

The Dual Rates function (è 14.2.3.) reduces total servo

travel, whereas Expo does not change the end-points.

This means that full travel is always available when re-

quired.

14.2.7. Parameter „Fixed value“

4 separately variable for each flight phase

F can be assigned to a 3-D digi-adjustor

-100% to 100%, 0% = OFF

This parameter is used to generate control surface trav-

els which cannot be changed by the associated trans-

mitter control.

A typical example for this function is a fixed flap posi-

tion for launching the model. When you switch on the

LAUNCH flight phase, the flaps are required to move

automatically to the launch position. In NORMAL flying

the flaps are controlled using a transmitter control (e.g.

slider F) in the normal way.

14.2.8. Parameter „Run time“ (Slow)

F can be assigned to a 3-D digi-adjustor

0.1 to 4.0 s

The run time parameter allows you to determine the

time over which a transmitter control moves from one

end-point to the other. This enables you to set up grad-

ual travel of any control system, even if it is triggered by

a switch.

Examples:

Extending retractable undercarriage slowly, so that

the process operates at scale speed.

Lowering or raising flaps slowly, so that the model does

not make any abrupt movements when you change the

flap setting.

14.2.9. Parameter „Idle“ (idle trim)

Throttle control only

This function alters the operation of the idle trim, as the

name indicates. From the graph in the H Throttle menu

you will see that the throttle trim only affects the range

up to centre (1/2-throttle). The area from centre to full-

throttle is not affected.

14.2.10. Parameter „Collective pitch“

(Coll. pitch curve)

I affects the active model only

Range +/- 100%

4 one coll. pitch curve for each flight phase

F each curve point can be assigned to a 3-D digi-

adjustor (è 10.2.2)

Adjusting the collective pitch curve for helicopters is

done in the menu H Control/Collect. Each flight

phase can have a separate curve, to adopt the curve to

each individual phase.

Example 1: Coll. pitch curve phase Hover

„Flattened“ curve between hover and collective pitch-

minimum for more sensitive hovering and landing.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex ROYALevo12 Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Multiplex ROYALevo12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info