Bedienungsanleitung NAD T 758 (Seite 18 von 42) (Englisch)

745046

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

DSP OPTIONS

LIP SYNC DELAY

DSP Options has the feature “Lip Sync Delay” whose function is to match

any delay that may occur in the picture relative to the audio.

By varying “Lip Sync Delay” from 0ms to 120ms, one can delay the audio

output in order to synchronize it with the video image.

TONE CONTROLS

The T 758 has two Tone Control levels – Treble and Bass. Bass and Treble

controls only aect the low bass and high treble leaving the critical

midrange frequencies free of coloration.

These controls allow one to tweak on-the-y, the frequency response

of the source during playback. The control setting could be adjusted by

navigating through the Tone Controls’ OSD menu via a combination of

[ENTER] and [ A/S/D/F ] keys.

Maximum and minimum values for all three Tone Control levels are ±10 dB.

“Tone Defeat” gives one the choice of varying or completely bypassing

the tone control section of the T 758. If “O” (“Tone Active” in the VFD) is

selected, the Tone Control circuits are active.

Select “On” (“Tone Defeat” in the VFD) to bypass the Tone Controls eectively

defeating the eect of the tone control circuits.

NOTE

Tone Controls options can be directly selected or changed using AVR 4’s

[TONE] button with DEVICE SELECTOR set to AMP mode. Toggle [TONE]

button to select “Treble” or “Bass” and then use the [D/F] to adjust their

respective levels. Press [TONE] again to save the settings and at the same

time move on to the next parameter or exit the parameter setting altogether.

ZONE CONTROLS

Depending on the settings made at the separate “Zone Setup” menu

under the “Setup Menu” section discussion, Zone 2 can be congured and

managed via this “Zone Controls” window.

Select “On” to activate Zone 2. When activated, the Source input for Zone

2 can be allocated by selecting through the following inputs – All enabled

Sources, Front Input, Media Player, Tuner and Local.

As long as the associated Source input is active, it will continuously be

available at ZONE 2 output port in the rear panel regardless of the Main

Zone settings. For example, while the T 758 is at Source 1 mode, you can

set the Zone 2 Controls’ “Source” item to “Source 3”; the active Source 3’s

audio output will be directed to ZONE 2 output port in the rear panel even

though the T 758 is at Source 1 mode.

You can then feed the ZONE 2 jacks to another amplier or receiver

that maybe located in another area of your home or building. With your

separate amplier or receiver selecting the fed signal and with speakers

connected, you can then enjoy the zone selected source’s audio signal.

Select “Local” as your selected Zone 2 Source input if you wish to enjoy the

same source as the main Zone and allow simultaneous listening, but with

full separate volume levels.

If a Zone 2 is set to “O”, it is deactivated or powered o.

ZONE 2 AT AUDIO PREOUT SURROUND BACK

SURR-BACK L and SURR-BACK R channels of AUDIO PRE-OUT can be

assigned as Zone 2 OUT. This is applicable only if “Zone 2” is the selected

setting of “Back Amp” in the “Amplier Setup” menu.

With this condition, the following are applicable

• The surround back amplier channels supply Zone 2 speaker level

output via the surround back speaker terminals. With this setup, Zone

2 audio/speaker level can be increased or decreased using the VOL

(Volume) keys of the supplied ZR 7 zone remote control.

• At the same time, Zone 2 (item 15 “ZONE 2” in the “IDENTIFICATION OF

CONTROLS – REAR PANEL” section) continues to send zone selected

audio source to the corresponding audio input of a separately located

additional amplier or receiver (not supplied) that can power its

matching set of speakers. Zone 2 audio level for this port is xed; it

cannot be adjusted by any ZR 7 volume command.

• On the other hand, the secondary Zone 2 at AUDIO PRE-OUT (item

14 “AUDIO PRE-OUT/ZONE 2” in the “IDENTIFICATION OF CONTROLS

– REAR PANEL” section) also sends zone selected audio source to the

corresponding audio input of a separately located additional amplier

or receiver (not supplied) that can power its matching set of speakers.

Zone 2 audio output for this secondary Zone 2 can be increased or

decreased using the VOL (Volume) keys of the supplied ZR 7 zone

remote control.

• For the applicable Zone 2 function, Zone 2 audio level can only be adjusted

using the Volume keys of ZR 7 remote control only if “Back Amp” in the

“Amplier Setup” menu is set to “Zone 2”. Setting “Back Amp” to “Main Front”

or “Main Back” will not allow Zone 2 audio level adjustment.

IMPORTANT NOTICE

Only analog audio connected through a Source’s analog audio input

port can be associated as audio source for Zone 2. Digital audio sources

connected via HDMI, digital optical and digital coaxial input ports

cannot be downmixed and used as Zone 2 audio source. Ensure also

that the associated Source’s Digital Audio setting is set to “O” or no

actual digital source is connected.

OPERATION

USING THE T 758  MAIN MENU

ENGLISH PORTUGUÊSFRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

NAD T 758 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD T 758

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info