Bedienungsanleitung NAD T 758 (Seite 21 von 42) (Englisch)

745046

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

DIGITAL AUDIO

To take advantage of the T 758’s high performance surround and digital

audio circuitry, it is advisable that its Digital Audio inputs are selected.

There are three types of Digital Audio input for the T 758. These are HDMI,

Optical and Coaxial digital inputs. A fourth option is “O” whereby no

incoming digital audio signal is selected by the particular Source.

The desired digital audio input for a particular Source can be selected by scrolling

to “Digital Audio”, press [ S ] and then [ D/F ] to step through the desired digital

input source. After nalizing the desired type of Digital Audio input, press [ S ]

and then [ D/F ] again to select the specic Digital Audio input.

The following are the sets of assignable Digital Audio input:

HDMI $ HDMI 1, HDMI 2, HDMI 3, HDMI 4

Optical $ Optical 1, Optical 2, Optical 3, Optical Front

Coaxial $ Coaxial 1, Coaxial 2, Coaxial 3

NOTE

An incoming digital signal present at the assigned digital input will always

take precedence over the assigned analog audio input, even if both are

present. To maintain the analog audio input for the particular Source, select

“O” at the “Digital Audio” setting of the same “Source” menu.

VIDEO

There are ve types of video input a particular Source could be assigned. These

are HDMI, Component, S-Video, Video and Previous inputs. A sixth option is “O”

wherein the particular Source is prompted not to select any Video input.

Navigate through the Video input selections by pressing [ S ] and then [ D/F ] to

step through the selections. The following are the sets of assignable Video input:

HDMI $ HDMI 1, HDMI 2, HDMI 3, HDMI 4

Component Video $ Component 1, Component 2, Component 3

S-Video $ S-Video 1

Video $ Video 1, Video 2, Video Front

Previous $ Display or retain preceding video.

IMPORTANT NOTE ABOUT THE VIDEO PERFORMANCE OF T 758

The T 758 utilizes an NAD-engineered eld-programmable gate array

(FPGA) that is capable of enabling the conversion of analog video to

digital video. This allows a single cable connection to your TV for all

sources while maintaining the source’s native resolution. Interlaced

video is converted to progressive scan over HDMI allowing complete

compatibility with latest HD TVs.

The T 758 also supports HDMI features that include compatibility with a

broad range of 3D and HD digital video sources and displays.

A/V PRESET

A particular Source can be assigned a stored Preset. The parameters set up

in the selected Preset number will be adopted into the particular Source it

is assigned (Please refer to the separate section on “A/V Presets” for further

understanding of Preset settings).

Scrolling to “A/V Preset” and by pressing [ S ] and then [ D/F ], a Source

could be assigned a Preset number ranging from Preset 1 to 5.

If it is desired not to assign the particular Source a Preset setting, select “O”.

TRIGGER OUT

The Trigger Out for a particular Source is dependent upon the

congurations done in a separate menu on Trigger Setup (See “Trigger

Setup” below).

For “Trigger Out” to become enabled and assignable at “Source Setup

(Normal View)” menu, make sure to carry out or note the following

beforehand

• In the separate “Trigger Setup” menu, assign “Trigger 1 Out” to “Source

Setup”.

• “Trigger Out” will not appear as an option at the Source Setup (Normal

View) menu if at the separate “Trigger Setup” menu, “Trigger 1 Out” is

assigned to “Main” or “Zone 2”.

Set “Trigger Out” to “On” to enable “Trigger Out” or “O’ to disable it as per

assigned Source.

SOURCE SETUP (TABLE VIEW)

The Source Setup (Table View) reects the settings made in the Source

Setup (Normal View) menu. All the Source settings are summarized and

displayed in tabulated form in the Source Setup (Table View).

Navigating through the Source Setup (Table View) via a combination of

[ A/S ] and then [ D/F ] buttons, one will have the benet of directly

changing the settings for “Audio”, “Video”, “Preset”, “Trigger” and “Source

Name” without going back to the Source Setup (Normal View) menu.

Highlight a particular Source number and then, toggle [ENTER] button to

enable or disable said Source number.

OPERATION

USING THE T 758  SETUP MENU

ENGLISHPORTUGUÊS FRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD T 758 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD T 758

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info