Bedienungsanleitung Onkyo TX-NR3008 (Seite 51 von 116) (Englisch)

553767

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

■ Speaker Impedance

` 4ohms:

Select if the impedance of any speaker is 4 ohms or

more but less than 6.

` 6ohms

Select if the impedances of all speakers are between

6 and 16 ohms.

Note

• When bridging is used, “Speaker Impedance” setting is fixed at

“8ohms”.

■ Speakers Type(Front A)

` Normal

Select this if you’ve connected your front speakers A

normally.

` Bi-Amp:

Select this if you’ve connected your front speakers A

for bi-amped operation. The Bi AMP indicator will

light (➔ 9).

` BTL:

Select this if you’ve connected your front speakers A

for bridged operation. The BTL indicator will light

(➔ 9).

Note

•“Bi-Amp” and “BTL” cannot be selected if “Speakers

Type(Front B)” is set to “Bi-Amp” or “BTL”.

• Surround back speakers and Powered Zone 3 cannot be used if

you select “Bi-Amp” or “BTL”.

•“Speakers Type(Front A)” is set to “Normal” if the “Front

High + Front Wide” setting is set to “Ye s ”.

■ Speakers Type(Front B)

` Not Use

Select this if you’re not using speakers B.

` Normal:

Select this if you’ve connected your front speakers B

normally.

` Bi-Amp:

Select this if you’ve connected your front speakers B

for bi-amped operation. The Bi AMP indicator will

light (➔ 9).

` BTL:

Select this if you’ve connected your front speakers B

for bridged operation. The BTL indicator will light

(➔ 9).

Note

•“Bi-Amp” and “BTL” cannot be selected if “Speakers

Type(Front A)” is set to “Bi-Amp” or “BTL”.

• Front high speakers, front wide speakers and Powered Zone 2

cannot be used if you select other than “Not Use”.

• Surround back speakers and Powered Zone 3 cannot be used if

you select “Bi-Amp” or “BTL”.

• This setting cannot be used if “Front High + Front Wide” set-

ting is set to “Ye s”.

■ Powered Zone 2, Powered Zone 3

See “Setting the Powered Zone 2/3” (➔ 82).

■ Front High + Front Wide

` Ye s:

Front High + Front Wide on.

` No

Front High + Front Wide off.

Listening mode that make use of “Front High + Front

Wide” setting is as follows;

Audyssey DSX (PLII/Neo:6 + Audyssey DSX included),

Orchestra, Unplugged, Studio-Mix, TV Logic, Game-

RPG, Game-Action, Game-Rock, Game-Sports, All Ch

Stereo, Full Mono.

Note

• When you have selected “Yes”,

–the “Surround Back” setting is set to “None”.

–the “Front High” or “Front Wide” setting is set to

“80Hz(THX)” if set to “None”.

•The “Front High + Front Wide” setting cannot be used in either

of the following cases;

–“Bi-Amp” or “BTL” is being used.

– Powered Zone 2/3 are being used.

Speaker Configuration

With these settings, you can specify which speakers are

connected and a crossover frequency for each speaker.

You can set the crossover frequencies, distances, and lev-

els of the front speakers A and front speakers B indepen-

dently. The other speakers (i.e., subwoofer, center,

surround, and surround back) use the same crossover fre-

quencies, distances, and levels for Speakers A and Speak-

ers B. Specify “Full Band” for speakers that can output

low frequency bass sounds adequately, for example,

speakers with a good sized woofer. For smaller speakers,

specify a crossover frequency. Sounds below the crossover

frequency will be output by the subwoofer instead of the

speaker. Refer to your speaker’s manuals to determine the

optimum crossover frequencies.

If you set up your speakers using Audyssey MultEQ XT32

Room Correction and Speaker Setup, please make sure

manually that any THX speakers are set to “80Hz(THX)”

crossover.

■ Subwoofer

` 1ch:

Audio signal is outputted from SW1 jack only.

` 2ch

Audio signal is outputted from SW1 and SW2

jacks.

` No:

Select if no subwoofer is connected.

This setting is set automatically by

Audyssey MultEQ

XT32 Room Correction and

Speaker Setup function (➔ 32). For Speakers B, you

need to change the settings manually.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR3008 Seite 51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR3008

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info