Bedienungsanleitung Onkyo TX-NR3008 (Seite 52 von 116) (Englisch)

553767

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

■ Front

(Setting Speakers A and Speakers B)

` Full Band

` 40Hz to 80Hz(THX)

to 100Hz, 120Hz, 150Hz,

200Hz

Note

•If the “Subwoofer” setting is set to “No”, the “Front” setting is

fixed at “Full Band”.

■ Center

, Surround

, Surround Back

*2*3*4*8

` Full Band

` 40Hz to 80Hz(THX)

to 100Hz, 120Hz, 150Hz,

200Hz

` None:

Select if no speaker is connected.

■ Front Wide

*1*2*6*7

, Front High

*1*2*5*7

` Full Band

` 40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,

200Hz

` None

Select if no speaker is connected.

Note

“Full Band” can be selected only when “Full Band” is

selected in the “Front” setting.

If the “Surround” setting is set to “None”, this setting cannot

be selected.

If the “Surround” setting is set to anything other than “Full

Band”, “Full Band” cannot be selected here.

If the “Powered Zone 3” setting is set to “Act” (➔ 82), or

“Bi-Amp” or “BTL” is being used (➔ 51), this setting cannot

be selected.

If the Powered Zone 2 is being used (➔ 82), this setting can-

not be selected.

If the “Powered Zone 2” setting is set to “Act” (➔ 82), this

setting cannot be selected.

If the “Speakers Type(Front B)” setting is set to “Normal”,

“Bi-Amp” or “BTL” (➔ 51), this setting cannot be selected.

This setting cannot be used if the “Front High + Front

Wide” setting is set to “Ye s ”.

■ Surround Back Ch

` 1ch:

Select if only one surround back speaker is con-

nected.

` 2ch

Select if two (left and right) surround back speakers

are connected.

Note

•If the “Surround Back” setting is set to “None”, this setting

cannot be selected.

■ LPF of LFE

(Low-Pass Filter for the LFE Channel)

` 80Hz, 90Hz, 100Hz, 120Hz

With this setting, you can specify the cutoff frequency

of the LFE channel’s low-pass filter (LPF), which can

be used to filter out unwanted hum. The LPF only

applies to sources that use the LFE channel.

■ Double Bass

With the Double Bass function, you can boost bass out-

put by feeding bass sounds from the front left, right, and

center channels to the subwoofer.

` On

Double Bass function on.

` Off(THX):

Double Bass function off.

Note

• This function can be set only if the “Subwoofer” setting is set to

“1ch” or “2ch”, and the “Front” setting is set to “Full Band”.

• If you’re using THX-certified speakers, select “Off(THX)”.

■ Subwoofer, Front, Center, Surround,

Surround Back

(Setting Speakers A and Speakers B)

` Not Use:

Select if you don’t want to use each speaker with

Speakers A or Speakers B.

` Use

Select if you do want to use each speaker with

Speakers A or Speakers B.

If you’re using Speakers B, you can choose whether or not

to use the subwoofer, center, surround, and surround back

speakers with the Speakers A and Speakers B configura-

tions independently. You cannot choose whether or not to

use the front speakers.

Note

• These settings can only be displayed when the “Speakers

Type(Front B)” setting is set to other than “Not Use” (➔ 51).

• You cannot select speakers that you set to “No” or “None”.

Speaker Distance

Here you can specify the distance from each speaker to the

listening position so that the sound from each speaker

arrives at the listener’s ears as the sound designer

intended.

You can set the distances for front speakers A and front

speakers B independently. The other speakers (i.e., sub-

woofer, center, surround, and surround back) use the same

distance settings for Speakers A and Speakers B.

■ Unit

` feet:

Distances can be set in feet. Range: “0.5ft” to

“30.0ft” in 0.5 foot steps.

` meters:

Distances can be set in meters. Range: “0.15m” to

“9.00m” in 0.15 meter steps.

(The default setting varies from country to country.)

This setting is NOT set automatically by

Audyssey MultEQ

XT32 Room Correction and

Speaker Setup function (➔ 32).

This setting is set automatically by

Audyssey MultEQ XT32 Room Correction and Speaker

Setup function (➔ 32). For Speakers B, you need to

change the settings manually.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR3008 Seite 52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR3008

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info