Bedienungsanleitung Onkyo TX-NR3008 (Seite 53 von 116) (Englisch)

553767

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

■ Left, Front Wide Left, Front High Left, Center,

Front High Right, Front Wide Right, Right,

Surround Right, Surround Back Right,

Surround Back Left, Surround Left,

Subwoofer 1, Subwoofer 2

` Specify the distance from the each speaker to your lis-

tening position.

Note

• Speakers that you set to “No” or “None” in the

“Speaker Configuration” cannot be selected (➔ 51).

• Speakers B cannot be selected if “Speakers Type(Front B)” is

set to “Not Use” (➔ 51).

If the “Subwoofer” setting is set to “1ch”, this setting cannot

be selected (➔ 51).

Level Calibration

Here you can adjust the level of each speaker with the

built-in test tone so that the volume of each speaker is the

same at the listening position.

The other speakers (i.e., subwoofer, center, surround, and

surround back) use the same level settings for Speakers A

and Speakers B.

■ Left, Front Wide Left, Front High Left, Center

Front High Right, Front Wide Right, Right,

Surround Right, Surround Back Right,

Surround Back Left, Surround Left

` –12.0dB to 0.0dB to +12.0dB in 0.5 dB step.

■ Subwoofer 1

, Subwoofer 2

*1*2

` –15.0dB to 0.0dB to +12.0dB in 0.5 dB step.

Note

• Speakers that you set to “No” or “None” in the

“Speaker Configuration” cannot be selected (➔ 51).

• The speakers cannot be calibrated while the AV receiver is

muted.

• The test tone is output at the standard level for THX, which is

0 dB (absolute volume setting 82). If you normally listen at vol-

ume settings below this, be careful because the test tone will be

much louder.

• Speakers B cannot be selected if “Speakers Type(Front B)” is

set to “Not Use”.

•The “Level Calibration” setting cannot be selected if “Audio

TV Out” setting is set to “On”.

For the center speaker and subwoofer, the level settings made

by using the Home menu are saved (➔ 30).

If the “Subwoofer” setting is set to “1ch”, this setting cannot

be selected (➔ 51).

Tip

• If you’re using a handheld sound level meter, adjust the level of

each speaker so that it reads 75 dB SPL at the listening position,

measured with C-weighting and slow reading.

Equalizer Settings

With the Equalizer settings, you can adjust the tone of

speakers individually with a 7-band equalizer. The volume

of each speaker can be set (➔ 53).

The Equalizer settings only apply to Speakers A and can-

not be adjusted while Speakers B is selected.

■ Equalizer

` Manual:

You can adjust the equalizer for each speaker manu-

ally. If you selected “Manual”, continue with this

procedure.

` Audyssey:

This is selected automatically by

Audyssey MultEQ XT32 Room Correction and

Speaker Setup function. The Audyssey indicator will

light (➔ 9) and “Dynamic EQ” and

“Dynamic Volume” become available (➔ 57).

When “Audyssey” is selected, “Dolby Volume”

becomes “Off” automatically (➔ 55).

` Off

Tone off, response flat.

This setting is set automatically by

Audyssey MultEQ

XT32 Room Correction and

Speaker Setup function (➔ 32). For Speakers B, you

need to change the settings manually.

This setting is set automatically by

Audyssey MultEQ XT32 Room Correction and Speaker

Setup function (➔ 32).

Press w to select “Channel”, and then use e/

r to select a speaker.

Use q/w to select a frequency, and then use

the e/r to adjust the level at that frequency.

The volume at each frequency can be adjusted

from –6dB to 0dB

to +6dB in 1 dB steps.

Note

• You can select: “63Hz”, “160Hz”, “400Hz”,

“1000Hz”, “2500Hz”, “6300Hz”, or “16000Hz”.

And for the subwoofer, “25Hz”, “40Hz”, “63Hz”,

“100Hz”, or “160Hz”.

• While the Direct or Pure Audio listening mode is

selected, the equalizer settings have no effect.

Tip

• Low frequencies (e.g., 63Hz) affect bass sounds;

high frequencies (e.g., 16000Hz) affect treble

sounds.

Use q to select “Channel”, and then use e/r

to select another speaker.

Repeat steps 1 and 2 for each speaker.

You cannot select speakers that you set to “No”

or “None” in the “Speaker Configuration”

(➔ 51).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR3008 Seite 53

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR3008

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info