Bedienungsanleitung Onkyo TX-NR579 (Seite 67 von 84) (Englisch)

462088

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

■ There’s no picture

■ There’s no picture from a source connected to

an HDMI IN

■ The on-screen menus don’t appear

■ The on screen display does not appear

■ Reception is noisy, FM stereo reception is

noisy, or the FM STEREO indicator doesn’t light

■ The remote controller doesn’t work

■ Can’t control other components

Video

Make sure that all video connecting plugs are pushed

in all the way.

Make sure that each video component is properly

connected.

15, 16

If your TV is connected to the HDMI OUT, select

“-----” in the “HDMI Input” setup to watch

composite video, and component video sources.

If the video source is connected to a component

video input, you must assign that input to an input

selector, and your TV must be connected to either

the HDMI OUT or COMPONENT VIDEO OUT.

16, 41

If the video source is connected to a composite video

input, your TV must be connected to the HDMI

OUT or the corresponding composite video output.

If the video source is connected to an HDMI input,

you must assign that input to an input selector, and

your TV must be connected to the HDMI OUT.

15, 41

While the Pure Audio listening mode is selected, the

video circuitry is turned off and only video signals

input through HDMI IN can be output.

—

On your TV, make sure that the video input to which

the AV receiver is connected is selected.

—

Reliable operation with an HDMI-to-DVI adapter is

not guaranteed. In addition, video signals from a PC

are not guaranteed.

When the resolution is set to any resolution not

supported by the TV, no video is output from the

HDMI outputs.

If the message “Resolution Error” appears on the

AV receiver’s display, this indicates that your TV

does not support the current video resolution and

you need to select another resolution on your DVD

player.

—

On your TV, make sure that the video input to which

the AV receiver is connected is selected.

—

When the AV receiver is not connected to a TV via

HDMI, onscreen menus are not displayed.

—

Depending on the input signal, the on screen display

may not appear when the input signal from the

HDMI IN is output to a device connected to the

HDMI OUT.

Tuner

Relocate your antenna. —

Move the AV receiver away from your TV or

computer.

—

Listen to the station in mono. 26

When listening to an AM station, operating the

remote controller may cause noise.

—

Passing cars and airplanes can cause interference. —

Concrete walls weaken radio signals. —

If nothing improves the reception, install an outdoor

antenna.

—

Remote Controller

Before operating this unit, be sure to press

RECEIVER.

—

Make sure that the batteries are installed with the

correct polarity.

Install new batteries. Don’t mix different types of

batteries, or old and new batteries.

Make sure that the remote controller is not too far

away from the AV receiver, and that there’s no

obstruction between the remote controller and the

AV receiver’s remote control sensor.

Make sure that the AV receiver is not subjected to

direct sunshine or inverter-type fluorescent lights.

Relocate if necessary.

—

If the AV receiver is installed in a rack or cabinet

with colored-glass doors, the remote controller may

not work reliably when the doors are closed.

—

Make sure you’ve selected the correct remote

controller mode.

10, 63

When using the remote controller to control other

manufacturers’ AV components, some buttons may

not work as expected.

—

Make sure you’ve entered the correct remote control

code.

Make sure to set the same ID on both the AV

receiver and remote controller.

If it’s an Onkyo component, make sure that the u

cable and analog audio cable are connected properly.

Connecting only an u cable won’t be enough.

Make sure you’ve selected the correct remote

controller mode.

10, 63

For a proper operation of the remote controller as a

cassette tape deck is connected to the TV/CD IN

jack, or as an RI Dock is connected to the TV/CD

IN, VCR/DVR IN or GAME IN jacks, you must set

the input display accordingly.

If you cannot operate it, you will need to enter the

appropriate remote control code.

To control another manufacturer’s component, point

the remote controller at that component.

To control an Onkyo component that’s connected

via u, point the remote controller at the AV

receiver. Be sure to enter the appropriate remote

control code first.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR579 Seite 67

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR579

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info