Bedienungsanleitung Panasonic DMPBD10A (Seite 26 von 32) (Englisch)

602952

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

RQT8966

Operation Page

Displays

TV screen and video

(Continued on the next page)

Cannot operate the television. ≥Change the manufacturer code. Some televisions cannot be operated even if you change the

code.

≥It may be necessary to set the manufacturer code again after changing the batteries.

The remote control doesn’t

work properly.

≥The remote control and main unit are using different codes. Change the code on the remote

control.

Press and hold [ENTER] and the indicated number button at the same

time for more than 2 seconds.

≥The batteries are depleted. Replace them with new ones.

≥You are not pointing the remote control at the main unit’s remote control signal sensor during

operation.

≥Coloured glass may obstruct the signal reception/transmission.

≥Don’t place the signal sensor in direct sunlight or in areas that may be subject to sunlight

exposure.

≥It may be necessary to set the code on the remote control again after changing the batteries.

—

The unit is on but cannot be

operated.

≥Some operations may be prohibited by the disc.

≥The unit is hot (“U59” appears on the display). Wait for “U59” to disappear.

≥One of the unit’s safety devices may have been activated.

Reset the unit as follows:

1 Press [Í/I] on the main unit to switch the unit to standby.

If the unit doesn’t switch to standby, press and hold [Í/I] on the main unit for about 10

seconds. The unit is forcibly switched to standby.

Alternatively, disconnect the AC mains lead, wait one minute, then reconnect it.

2 Press [Í/I] on the main unit to switch it on. If the unit still cannot be operated, consult the

dealer.

≥Condensation has formed: Wait 1 to 2 hours for it to evaporate.

—

Play fails to start even when

[1] (PLAY) is pressed.

Play starts but then stops

immediately.

≥Insert the disc correctly with the label facing up.

≥The disc is dirty.

≥You tried to play a blank disc or unplayable disc on this unit.

4, 5

The Video CD picture does not

display properly.

≥When connecting to multi-system TV, select “NTSC” in “TV System” in the Setup menu.

≥When connecting to PAL TV, the lower part of the picture cannot be displayed correctly

during search.

—

Time Slip does not work. ≥Time Slip does not work when the unit’s “TV System” settings are different from the title

recorded on the disc.

Cannot eject disc. ≥The unit may have a problem. While the unit is off, press and hold [;] and [5/9] on the

main unit at the same time for about 5 seconds. Remove the disc and consult the dealer.

—

Startup is slow.

When the unit is turned on,

audio and video output takes a

long time.

≥Startup takes time in the following situations.

–Immediately after a power failure or the AC mains lead is connected.

–When the unit is connected with an HDMI cable.

—

The display is dim. ≥Change “FL Display” in the “Display” tab of the Setup menu. 22

The elapsed time displayed is

actually less than the playtime.

≥The displayed play time is converted from the number of frames at 29.97 frames (equal to

0.999 seconds) to one second. There will be a slight difference between the time displayed

and the actual elapsed time (e.g., actual one-hour elapsed time may display as

approximately 59 minutes 56 seconds).

—

The images from this unit do

not appear on the television.

Picture is distorted.

The television may display

incorrectly or colours appear

faded.

≥Make sure that the television is connected to the AV terminal, VIDEO OUT terminal, S

VIDEO OUT terminal, COMPONENT VIDEO OUT terminals or HDMI AV OUT terminal on

this unit.

≥Make sure that the television’s input setting (e.g., AV 1) is correct.

≥Progressive output is set to on but the connected television is not progressive compatible.

While stopped, press and hold [∫] and [1] (PLAY) on the main unit at the same time for

more than 5 seconds to cancel this setting. The setting will change to interlace.

≥Set “Transfer” in Picture menu to “Auto”.

≥The unit and television are using different video systems. While stopped, keep pressing [∫]

and [< OPEN/CLOSE] on the main unit for 5 or more seconds. The system switches from

PAL t o

NTSC

or vice versa.

≥The system used on the disc doesn’t match your television.

–

PAL discs cannot be correctly viewed on an NTSC television.

–This unit can convert NTSC signals to PAL60 for viewing on a PAL television (“TV System” in

the “Connection” tab).

–]BD-V] This unit cannot convert BD-Video from NTSC signals to PAL60 signals; therefore

video cannot be displayed properly when you connect this unit to the AV terminal, VIDEO

terminal or S VIDEO terminal.

8, 9

—

Video is not output in high

definition.

≥High definition video cannot be output through the AV, VIDEO OUT or S VIDEO OUT

terminals.

≥Depending on the BD-Video, output from the COMPONENT VIDEO OUT terminals may be

restricted to 576p/480p.

—

RGB video is not output from

the AV terminal.

≥When connecting to an amplifier/receiver with an HDMI cable, set “HDMI Video Mode” in the

“

HDMI

” tab to “Off”.

Status messages do not appear.

≥Select “Automatic” in “On-Screen Messages” of the “Display” tab in the Setup menu. 22

The 4:3 aspect ratio picture

expands left and right.

Screen size is wrong.

≥Use the television to change the aspect. Refer to your television’s operating instructions.

≥If connecting with a component video cable, set “Progressive” to “Off” in the Picture menu. If

this doesn’t help or you cannot set it to “Off”, then set the “TV Aspect” of the “Connection” tab

to “4:3 Pan & Scan” in the Setup menu.

—

20, 22

Reference 11 Troubleshooting guide

DMP-BD10A.book Page 26 Thursday, March 15, 2007 7:45 PM

Panasonic DMPBD10A Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic DMPBD10A

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info