Bedienungsanleitung Parkside PDFW 120 A2 - IAN 353549 (Seite 13 von 65) (Englisch)

762964

Zoom out

Zoom in

Vorherige Seite

1/65

Nächste Seite

PDFW 120 A2 GB│IE│NI│CY │ 9 ■

c) Do not use toothed saw blades. Such acces-

sories often cause a kickback or loss of control

over the power tool.

d) Always move the accessory tool in the same

direction in the material in which the cutting

edge leaves the material (in other words, the

same direction in which the dust is thrown

out). Guiding the power tool in the wrong direc-

tion will cause the cutting edge of the accessory

tool to jump out of the workpiece which can

lead to the accessory tool being pulled in this

direction.

e) Always ﬁx the workpiece when using rotary

ﬁles, cutting discs, high-speed milling tools or

hard-metal tools. Even a minimal tilting in the

groove can cause these tools to jam and lead

to a kickback. When the cutting disc jams, it

usually breaks. When a rotary ﬁle, high-speed

milling tool or hard-metal milling tool jams, the

accessory tool can jump out of the groove and

lead to loss of control of the power tool.

Supplementary safety instructions

for grinding and abrasive cutting

Special safety instructions for grinding and

abrasive cutting

a) Use only the grinding accessories approved

for your power tool and only for the recom-

mended applications. Example: Never grind

with the side surface of a cutting disc. Cutting

discs are designed to remove material with

the edge of the disc. Any lateral application

of force on these grinding tools can lead to

breakage.

b) Use only undamaged mandrels of the correct

size and length and without undercut on the

shoulder for conical and straight pencil

grinders. Using an appropriate mandrel

reduces the risk of breakages.

c) Avoid cutting disc jams or excessive contact

pressure. Do not make any excessively deep

cuts. Overloading the cutting disc increases the

stress and likelihood of tilting or blocking and

thus the possibility of a setback or a breakage

of the grinding tool.

d) Avoid putting your hand in the area in front

of or behind the rotating cutting disc. When

you move the cutting disc away from your hand,

it is possible, in the event of a kickback, that the

power tool along with the rotating disc could be

thrown out directly towards you along with the

rotating disc.

e) If the cutting disc jams or you stop working,

switch the tool oﬀ and hold it steady until the

disc has completely stopped turning. Never

attempt to pull a rotating cutting disc out of a

cut. This could lead to kickback. Identify and

remove the cause of the jam.

f) Do not switch the power tool back on as long

as it is in the workpiece. Allow the cutting disc

to reach its full speed before you carefully

continue the cut. Otherwise, the disc may jam,

jump out of the workpiece or cause kickback.

g) Support panels or large workpieces to

reduce the risk of the cutting disc jamming

and causing a kickback. Large workpieces can

bend under their own weight. The workpiece

must be supported on both sides, namely in the

vicinity of the cut, and also at the edge.

h) Be particularly careful when making “pocket

cuts” into existing walls or other obscured

areas. The inserted cutting disc may cut into

gas or water pipes, electrical wiring or other

objects that can cause kickback.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PDFW 120 A2 - IAN 353549 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PDFW 120 A2 - IAN 353549

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info