Bedienungsanleitung Pioneer GM-ME400X4 (Seite 3 von 8) (Englisch, Französisch)

811526

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Connecting the speakers

The speaker output mode can be four-channel,

three-channel (stereo and mono) or two-chan-

nel (stereo or mono). Connect the speaker

leads based on the mode and the figures

shown below.

Four-channel output

1Left

2Right

3Speaker output A

4Speaker output B

Two-channel output (Stereo)

1Speaker output (Right)

2Speaker output (Left)

Two-channel output (Mono)

1Speaker output (Mono)

Three-channel output

1Left

2Right

3Speaker output A

4Speaker output B (Mono)

Connections when using

the RCA input jack

Connect the stereo RCA output jack and the

RCA input jack of the amplifier.

!The RCA output jack of this unit outputs

the signal that comes from The RCA input

jack A.

<5707000013050V>9

Connecting the units

Four-channel / Three-channel output

!Slide INPUT SELECT (input select) switch

to 4CH position.

1RCA input jack A

2RCA input jack B

3Connecting wires with RCA plugs (sold sepa-

rately)

4From stereo (RCA output)

If only one input plug is used, e.g. when the

stereo has only one output (RCA output), con-

nect the plug to RCA input jack A rather than

5INPUT SELECT (input select) switch (4CH po-

sition)

Two-channel output (Stereo) / (Mono)

!Slide INPUT SELECT (input select) switch

to 2CH position.

1RCA input jack A

For two-channel output, connect the RCA

plugs to the RCA input jack A.

2Connecting wire with RCA pin plugs (sold se-

parately)

3From stereo (RCA output)

4INPUT SELECT (input select) switch (2CH

position)

Connections when using

the speaker input wire

Connect the stereo speaker output wires to

the amplifier using the supplied speaker input

wire with RCA pin cord.

1Stereo

2Speaker output

3Red: Right +

4Black: Right *

5Black: Left *

6White: Left +

7Speaker input wire with RCA pin cord

To the RCA input jack of this unit

Notes

!If speaker input wires from a headunit are

connected to this amplifier, the amplifier will

automatically turn on when the headunit is

turned on. When the headunit is turned off,

the amplifier turns off automatically. This

function may not work with some headunits.

In such cases, please use a system remote

control wire (sold separately). If multiple am-

plifiers are to be connected together synchro-

nously, connect the head unit and all

amplifiers via the system remote control wire.

!This amplifier automatically selects an input

signal mode between the RCA level and the

speaker level by detecting an input signal.

<5707000013050V>10

Connecting the units

Solderless terminal

connections

!Since the wire may become loose over

time, it must be periodically inspected and

tightened as necessary.

!Do not solder or bind the ends of the

twisted wires.

!Fasten while making sure to not to clamp

the insulating sheath of the wire.

!Use the supplied hexagonal wrench to

tighten and loosen the terminal screw of

the amplifier and use it to securely fasten

the wire. Be careful to avoid excessive tigh-

tening of this screw, which may damage

the wire.

Connecting the power terminal

WARNING

If the battery wire is not securely fixed to the term-

inal using the terminal screws, there is a risk of

overheating, malfunction and injury, including

minor burns.

!Always use the recommended battery and

ground wire, which is sold separately. Con-

nect the battery wire directly to the boat

battery positive (+) terminal and the

ground wire to the boat body.

!Recommended wires size (AWG: American

Wire Gauge) is as follows. The battery wire,

the ground wire and the optional direct

ground wire must be same size.

!Use a wire of 12 AWG to 16 AWG wire for

the speaker wire.

1 Route battery wire from engine com-

partment to the boat interior.

!When drilling a cable pass-thru into a bulk

head or barrier wall, route the cable

through carefully and seal the hole to pre-

vent fumes from seeping from engine com-

partment to other areas.

After completing all other amplifier connec-

tions, finally connect the battery wire terminal

of the amplifier to the positive +battery term-

inal.

1Positive +terminal

2Battery wire (sold separately)

The maximum length of the wire between

the fuse and the positive +terminal of the

battery is 30 cm (12 in.).

3Fuse (60 A) (sold separately)

Each amplifier must be separately fused at

60 A.

2 Use wire cutters or a utility knife to

strip the end of the battery wire, ground

wire and system remote control wire to ex-

pose about 10 mm (3/8 in.) of the end of

each of the wires, and then twist the ex-

posed ends of the wires.

Twist

10 mm (3/8 in.)

3 Connect the wires to the terminal.

Fix the wires securely with the terminal

screws.

<5707000013050V>11

Connecting the units

1Battery wire

2Power terminal

3Ground wire

4GND terminal

5System remote control wire

6System remote control terminal

7Terminal screws

Connecting the speaker output

terminals

1 Use wire cutters or a utility knife to

strip the end of the speaker wires to ex-

pose about 10 mm (3/8 in.) of wire and

then twist the wire.

Twist

10 mm (3/8 in.)

2 Connect the speaker wires to the

speaker output terminals.

Fix the wires securely with the terminal

screws.

1Terminal screws

2Speaker wires

3Speaker output terminals

Before installing the amplifier

WARNING

!To ensure proper installation, use the supplied

parts in the manner specified. If any parts

other than those supplied are used, they may

damage internal parts of the amplifier, or be-

come loose causing the amplifier to shut

down.

!Do not install in:

—Places where injury could occur if the boat

stops suddenly.

—Places where it may interfere with the

boat's operator.

!Install tapping screws in such a way that the

screw tip does not touch any wire. This is im-

portant to prevent wires from being cut by vi-

bration of the boat, which can result in fire.

!Make sure that wires do not get caught in the

sliding mechanism or touch the legs of a per-

son in the boat as short-circuit may result.

!When drilling to install the amplifier, always

confirm no parts are behind the panel and

protect all cables and important equipment

(e.g. cables, wiring, hoses, and modules) from

damage.

CAUTION

!To ensure proper heat dissipation of the ampli-

fier, ensure the following during installation:

—Allow adequate space above the amplifier

for proper ventilation.

—Do not cover the amplifier.

!Place all cables away from hot places, such

as near the heater outlet.

!The optimal installation location differs de-

pending on the boat model. Secure the ampli-

fier at a sufficiently rigid location.

!Check all connections and systems before

final installation.

<5707000013050V>12

Connecting the units Installation

Pioneer GM-ME400X4 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer GM-ME400X4

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info