Bedienungsanleitung Sanibroyeur SANICUBIC 2 Classic Expert-line (Seite 7 von 49) (Alle Sprachen)

532739

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

DESCRIPTION

The SANICUBIC

Classicis a lifting station

designed to evacuate effluent from small

private or commercial units.

Please comply with all the installation and

maintenance specifications set out in these

instructions, and especially the information

marked with the following signs:

" " Failure to comply with this

information could entail safety

hazards for personnel,

" " Information warning of the presence

of an electrical hazard,

" " Instructions only for qualified

professional specialists,

WARNING" Failure to comply with this

information could affect the normal

operation of the equipment.

Please contact our Customer service for

further information.

SANICUBIC OPERATING

PRINCIPLE

SANICUBIC

Classiccontains 2 separate

pumps. Each of the pumps is fitted with a

high-performance maceration system.

The 2 pumps operate alternately. In the

event of inflow overload, both motors run

at the same time (or if one of the pumps is

faulty, the other one takes over).

The SANICUBIC

Classictank is fitted with

2 dip tubes; one tube controls motor

operation, and the other one controls the

alarm system.

- Long pickup tube (normal operation):

as soon as the waste water level in the

tank reaches the triggering point in the

long tube, the pumping system starts up.

- Short pickup tube (inflow overload

operation): if the waste water level in the

tank reaches the upper point, a contact is

closed, and the auxiliary pumping system

is triggered. The contact also sets off an

audible and visual alarm. The general

alarm LED on the SANICUBIC

Classic

control panel switches to red.The

SANICUBIC

Classiccan be fitted with an

optional remote alarm unit (cabled) that

monitors the equipmentʼs operational status

by producing accoustic and visual signals.

LIST OF PARTS SUPPLIED

DIMENSIONS

TECHNICAL DATA

SANICUBIC

Classic

Type

R300 LC

Maximum discharge head

11 m

Voltage 220-240V

Frequency 50 Hz

Volume 47 l

Maximum power input 3000 w

Maximum current input 13 A

Electrical classification I

Ave water temp for optimum performance 35°C

Maximum temperature intermittent

(max 5 min) 70°C*

Protection index IP67

Net weight (including accessories) 30 kg

Hot water drain cycles from dishwashers or washing machines

FIELD OF APPLICATION

Household waste water (the combined

inputs must not exceed 80% of those

shown in the graph ).

INSTALLATION

The SANICUBIC

Classicmust be instal-

led in compliance with standard EN12056.

The equipment must be commissioned

and maintained by a qualified professional

specialist.

Please refer to installation standard

EN 12056.

REGULATIONS

1- Attention: the space in which the

SANICUBIC

Classicis to be installed

must be large enough to leave at least

600 mm of working room around and

above the unit to facilitate such

maintenance work as may be required.

There must be sufficient lighting, and it

must be sufficiently well ventilated and

protected from freezing.

2- Isolating valves (not supplied) must

be fitted on waste inlets (especially

the 110mm inlets) and on the

discharge to ensure that any

service/maintenance may be carried

out safely).

3- The discharge pipe must be fitted so as

to avoid all back flow from the drainage

system (see the examples in drawing

). Back flow can be avoided by

installing an anti-back flow riser

reaching a high point above the

maximum back flow level.

Comment: In the absence of local

information to the contrary, the

maximum back flow level corresponds

to street level (roadway, pavements,

etc.). Continue the discharge pipework

after the anti-backflow riser, using a

larger diameter pipe.

4- If the Sanicubic is installed in a space

such as a pit for example, we would

recommend the fitting of a bilge pump

in case of flooding.

5- The lifting station must be vented with

an outlet at roof level.

6- The lifting station must be fixed to the

floor (see paragraph ).

CONNECTING THE DISCHARGE

PIPE

Remove the end cover or covers from the

back of the unit (cf. ).

As each pump is fitted with a macerator

system, an ND50 mm discharge pipe can

be used.

The discharge bend is at the centre of the

unit, at the back (cf. ). Use the sleeve

to connect it to the riser pipe and fix it

in place with the collars.

Each pump in the SANICUBIC

Classic

unit is fitted with check valves.

See paragraph regarding control

valves and back flow.

CONNECTING SANITARY

EQUIPMENT TO THE LOWER

INLETS

If you want to install a shower or a

bath at the same level as the

SANICUBIC

Classic, you must

make sure that the upper parts of the

plugholes on the sanitary equipment are

at least 250 mm above the lower inlets.

CONNECTING THE INLETS ND 40/50

Lower inlets (cf. )

Upper inlets (cf. )

• Cut off the end of the ND 50 inlet with a

saw

• Cut the sleeve to suit the pipe

diameter: ND 40 or ND 50 (cf. )

• Fix the sleeve on the inlet and on the

pipe, using the collars.

CONNECTING THE ND 100/110 INLET

Lower inlets (cf. )

1- Remove the plug from the side inlet.

2- Fix the sleeve in place using the

collar. .

3- Fully insert the ND 100/110 tube in the

other end of the sleeve and fix it in

place using the other collar. .

Upper inlets (cf. )

1- Cut off the upper end of the ND 100

inlet with a saw.

2- Fix the sleeve in place using the

collar .

3- Fully insert the ND 100/110 tube in the

other end of the sleeve and fix it in

place using the other collar .

CONNECTING THE VENT

1- VENT OFSANICUBIC

Classic

One of the upper ND50 inlets must

be used for the vent. The vent pipe

must be fitted up to roof level.

Cut off the end of the one of the ND

50 inlets with a saw.

Then fix the sleeve in place using

the collar .

Fully insert the ND 50 tube in the

other end of the sleeve and fix it in

place using the other collar .

WARNING: Do NOT fit air admittance

valve on the top of the air vent pipe.

The vent must be an open vent or the

unit will not operate.

2- VENTING THE ELECTRICAL PART

Connect the 8/11 clear PVC tubing

supplied to the keyboard on the

Sanicubic. The other end of this

tubing must be located between 1m

and 2m above the device to avoid

water getting into the electrical part

in the event of flooding.

Important: do not pinch the tubing.

PERFORMANCE CURVE

Example: Pump P1 is operating normally.

It discharges 160 l/min at a pumping

height of 5 m. If pump P1 shows any

signs of weakness or if the waste water

inflow is too great, pump P2 starts up. The

output is then increased to about 275

l/min, until the situation returns to normal.

The numbers refer to the explanatory diagrams.

RATIO OF HEIGHT/LENGTH

FOR

DISCHARGE

Fully illustrated step by step

instructions are downloadable

on www.saniflo.co.uk

9257 N150 SANICUBIC NOTICE:5622 NOTICE N°129 EXE 19/11/10 13:36 Page 6

Sanibroyeur SANICUBIC 2 Classic Expert-line Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info