Bedienungsanleitung Satel CA-10 (Seite 14 von 43) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

12 Installer Manual SATEL

Operation with the computer can be realized in two ways: in the „local mode” by means of the

RS-232 port with RJ socket (after connecting the CA-10 directly to one of the computer COM

ports), or in the „remote mode”, via the telephone line (in this case the computer must be

equipped with a modem).

Programming the data of LCD keypad is available in the local mode through the RS-232 port

on the keypad board. The DLOAD10 program, delivered with the panel, supports both

operating modes.

The DLOAD10 program enables:

• downloading (reading) all control panel parameters,

• uploading (writing) new parameters to the control panel,

• downloading (reading) the system event log,

• ON LINE operation.

The program does not read or change the user access codes – these are only

accessible through the user functions from keypads.

In the ON LINE mode, the computer displays current information on the system state,

including zone violations, active outputs, control panel clock, and selected partition state.

Provision is made for controlling the system in the same way as with a LED keypad.

The computer screen keypad works in parallel with the real keypads in partitions, therefore

commands for all partitions can be given from one place. The ON LINE mode also permits

downloading troubles and programming the clock.

Communication in the local mode (through the RS-232 port) is started with a special service

function (FS112). Connection can also be initialized without using the keypad (e.g. if it is

located far from the control panel and the computer). This can be achieved using the "Local

connection with…" command in the DLOAD10 program.

Communication through the telephone line can be initialized in three modes:

1) The computer calls the control panel, which after answering the call exchanges

handshake signals with the computer. When they are correct, the panel confirms

acceptance of the remote programming command, hangs up and calls back to the

computer using a number preprogrammed in the control panel. Prior to calling the

computer back, the panel notifies the monitoring station that the programming has

started.

2) The computer calls the control panel and, after the handshake, the control panel

immediately proceeds to the exchange of data. This simplified mode of establishing

communication is reached when the computer telephone number is not entered in the

control panel. Notification of the monitoring station will take place after communication

with the computer is over.

3) Establishing of communication from the control panel by calling the user function 0

(zero). The control panel first notifies the monitoring station that the programming has

started (when monitoring is active), then it dials the computer telephone number.

In order to reduce the cost of telephone connections, multiple suspension of the transmission

is possible. At the next connection, the control panel does not inform the monitoring station of

remote programming. Only after receiving the command to end the communication,

a message on completing the remote programming is sent to the station.

Initialization of communication can be disabled from the computer. When the communication

is suspended from the computer, the control panel is waiting for a call from the computer for

four hours even when the functions of automatically answering the computer call are

disabled. When the communication is ended with the “end” command instead of “suspend”,

the information on ending the communication is entered into the event log and sent to the

monitoring station after four hours.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info