Bedienungsanleitung Satel CA-10 (Seite 15 von 43) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

CA-10 Installer Manual 13

As the control panel is only accessible to the service, a number of protective devices is

provided to prevent hacking of the system and change of any data by unauthorized persons.

All the data exchanges are authorized by changing the access codes and the data are

encoded.

The DOWNLOADING can be particularly useful to installation firms engaged in servicing

many alarm systems. Then the user suggested inspections and modifications of software will

not necessarily require troublesome and costly traveling – they will be carried out with a

computer via the telephone line. Such a method of customer service and technical control of

customer systems will allow creation of alarm equipment services at an advanced and

professional level.

INSTALLATION OF THE CONTROL PANEL

Description of control panel main board

The control panel main board contains electronic components sensitive to

electric charges. Prior to installation, these charges must be removed. During

installation, avoid touching any elements on the control panel main board.

Explanations for Fig. 1:

1. The Battery cables – connect the red one to the battery terminal “+” and the black one to

the battery terminal “-“. The battery circuit is protected with a 2.5 A polymer fuse. Metal

connectors, which come with the control panel, can be used for connecting cables to the

battery (bolted connection, e.g. 17 Ah battery). Owning to that the battery cables lugs

should not be cut off.

2. The J20 pins are used for setting the battery charging current:

350 mA – pins shorted,

700 mA – pins open.

3. The RJ socket for connection of the control panel RS-232 port to the computer.

The RS-232 port is intended for programming the alarm system parameters from the

computer. For programming, a cable available in the kit designated DB9F/RJ-KPL is

required.

Notes:

• Do not short or touch the connector pins with your fingers.

• Prior to connecting the cable, the installer should first remove the electrostatic charge

e.g. touching a grounded fixture (a faucet or a heater) with the top of his hand.

• It is recommended that the cable be first connected to the control panel, and then to the

computer.

• The cable connecting the RS-232 ports may be up to twenty meters long.

4. The „DIALER” LED is on during telephone messaging by the panel, and blinks during

pulse dialing of the telephone number.

5. The J19 „RESET” pins make it possible to start the service mode without entering any

service code. This function can be disabled by the installer with software means (service

function FS131).

6. The BATTERY CHARGE LED situated next to the „J19” pins is on when the battery status

is being tested by the module and during charging of discharged battery. CA-10 tests the

presence of battery every 10 seconds and every 4 minutes it tests (for several seconds)

the battery status. During testing, the processor reduces the power supply and the loads

are powered from the battery. If the battery voltage drops down to 9.5 V, the control panel

will cut off the battery in order to prevent it from a complete discharge and damage.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info