Bedienungsanleitung Satel CA-10 (Seite 12 von 43) (Englisch)

699577

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

10 Installer Manual SATEL

3) Zone state display – LED standard. This mode is similar to the mode 2.

The difference is that in the second line the state of 12 zones of the control panel is

being monitored in the same way as it is the case in the LED keypad.

The operating mode 1 or 2 is recommended for the LCD keypad. Having selected the

mode 1, the user can temporarily switch the display between the text mode and the zone

state mode by holding down the ▼ key.

The operating mode is defined by the installer with the Status format service function

(Service Mode; LCD Keypad; Settings; Status format), available only after

activation of the control panel service mode.

The LCD keypad is fitted with a RS-232 port to enable programming the keypad settings

directly from the computer (see section: Activating selected functions).

Monitoring

The CA-10 control panel can transmit information about the system (partition) status to one

or two monitoring stations. Communication with the monitoring stations takes place

irrespective of the voice messaging and the messaging to paging systems. It has a priority

and is realized before the voice messaging. In case problems occur with getting connected to

the station, the control panel will suspend dialing the station number for 60 seconds and, if

the message is also to be transmitted by the dialer, it will make the line available to the dialer.

There are a few ways of transmitting information to the monitoring stations.

• Reporting to one station.

• Reporting to Station 1, and if unavailable – to Station 2 (e.g., when the station has two

telephone numbers). If this is the case, all events are reported, irrespective of which

station was reached by the control panel.

• Reporting to both stations with event sorting – depending on what event occurred in

the system, e.g. information on alarms to Station 1, and information on troubles to

Station 2 (this mode is useful where the station serves many subscribers and it is

necessary that the number likely to receive most vital information be busy as little as

possible). In this mode, during control panel programming, you can determine which

information is to be sent to which station.

• Reporting to both stations: Station 1 first, then Station 2. This mode is reached by

assigning the same event to both stations.

In case of a system with 16 zones and 32 users, the number of messages to be sent to the

monitoring station in order to ensure an appropriate facility protection degree may be large

enough to exceed the capacity of standard transmission formats. Therefore, to increase the

control panel flexibility, the events occurring in the system have been divided into six groups:

• the first one includes the zone related events (this group has the highest priority),

• four groups are represented by the partition related events (the event priority depends

on the partition number, the first partition having the highest priority),

• the sixth group accounts for the other system events.

Individual system identifiers are assigned to each group of events (one for each station).

In the event of stations which cannot accept several different identifiers in one

communication session, the control panel can send the events in separate sessions, in the

order resulting from the priority, grouping events with the same identifiers.

It is possible to send information on nine different zone related events and seventeen

partition related events (whereof seven events may contain the user number). The control

panel is also capable of sending twenty six other events which occurred in the system (e.g.

troubles, start of programming mode via a telephone, activation of service mode, etc.).

The event codes for both stations are the same. For a majority of events, it is possible to

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-10 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info