Bedienungsanleitung Scheppach HC08 (Seite 16 von 96) (Deutsch, Englisch, Dänisch, Französisch, Italienisch, Schwedisch)

758664

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

16 І 96

9. Electrical connection

The electrical motor installed is connected and

ready for operation. The connection complies with

the applicable VDE and DIN provisions.

The customer‘s mains connection as well as the

extension cable used must also comply with these

regulations.

Damaged electrical connection cable

The insulation on electrical connection cables is often

damaged.

This may have the following causes:

• Passage points, where connection cables are passed

through windows or doors.

• Kinks where the connection cable has been improp-

erly fastened or routed.

• Places where the connection cables have been cut

due to being driven over.

• Insulation damage due to being ripped out of the wall

outlet.

• Cracks due to the insulation ageing.

Such damaged electrical connection cables must not be

used and are life-threatening due to the insulation damage.

Check the electrical connection cables for damage reg-

ularly. Make sure that the connection cable does not

hang on the power network during the inspection.

Electrical connection cables must comply with the ap-

plicable VDE and DIN provisions. Only use connection

cables with the marking „H05VV-F“.

The printing of the type designation on the connection

cable is mandatory.

AC motor

• The mains voltage must be 230 V~

• Extension cables up to 25 m long must have a cross-

section of 1.5 mm2.

Connections and repairs of electrical equipment

may only be carried out by an electrician.

Please provide the following information in the event

of any enquiries:

• Type of current for the motor

• Machine data - type plate

10. Cleaning, maintenance, and storage

n Important!

Pull out the power plug before doing any cleaning and

maintenance work on the equipment. Risk of injury from

electric shock!

n Important!

Wait until the equipment has cooled down completely!

Risk of burns!

n Important!

Always depressurize the equipment before carrying out any

cleaning and maintenance work! Risk of injury!

8.2 Checking the oil level (Figure 7 - 9)

m Warning: For the rst use, check the oil level of

the compressor.

1 Operating the machine without oil will cause irrepara-

ble damage and render the warranty invalid.

2 Remove the plastic oil inlet plug on top of the crank

box of the compressor casing. (see g. 7)

3 Check the oil level in the sight glass (10). The oil level

should be in the centre of the red circle. (see g. 8

pos. 10.1)

4 Attach the closing plug (9), which is included and pull

it tight. (g. 9)

8.3 Mains connection

• The compressor is equipped with a mains cable with

shock-proof plug. This can be connected to any 230-

240 V~ 50 Hz shock-proof socket which is protected

by a 16 A fuse.

• Before you use the machine, make sure that the

mains voltage is the same as the operating voltage

(see the rating plate).

• Long supply cables, extensions, cable reels etc.

cause a drop in voltage and can impede motor start-

up.

• At low temperatures below +5°C, sluggishness may

make starting difcult or impossible.

8.4 ON/OFF switch (Fig. 3 Pos. 17)

• Pull the ON/OFF switch (17) upwards to switch on the

compressor. To switch off the compressor, press the

ON/OFF switch (17) down.

8.5 Setting the pressure (Fig. 3)

• Use the pressure regulator (16) to set the pressure on

the pressure gauge (14).

• The set pressure can be drawn from the quicklock

coupling (15).

• The vessel pressure can be read off the pressure

gauge (13).

8.6 Setting the pressure switch

• The pressure switch (2) is set at the factory.

Cut-in pressure approx. 6 bar

Cut-out pressure approx. 8 bar.

8.7 Overload protection switch (g. 1 pos. 8)

• The compressor has an automatic protection against

thermal overload. The overload protector is activated

at high engine temperature.

• The device is turned off. Re-commissioning of the de-

vice can be done only after cooling down and manual

reset.

• Follows after activation:

– Let the unit cool down

– Press the overload protection switch (8)

• Start the device as described under 8.4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HC08 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info