Bedienungsanleitung Scheppach HC08 (Seite 15 von 96) (Deutsch, Englisch, Dänisch, Französisch, Italienisch, Schwedisch)

758664

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

15 І 96

customer service workshop.

Do not lose these safety instructions

6. Technical data

Mains connection 230 V~ 50 Hz

Motor rating W max. 1100

Operating mode S1

Compressor speed min-1 2850 min-1

Pressure vessel capacity (in liters) 8

Operating pressure approx. 8 bar

Theoretical intake capacity (l/min) approx. 155

sound power level LWA 93 dB(A)

uncertainty KWA 1.9 dB

Protection type IP20

Weight of the unit in kg 15

The noise emission values were measured in accord-

ance with EN ISO 3744.

Wear hearing protection.

The effects of noise can cause a loss of hearing.

7. Before starting the equipment

Before you connect the equipment to the mains supply

make sure that the data on the rating plate are identical

to the mains data.

• Check the equipment for damage which may have

occurred in transit. Report any damage immediately

to the transport company which was used to deliver

the compressor.

• Install the compressor near the point of consumption.

• Avoid long air lines and supply lines (extension ca-

bles).

• Make sure that the intake air is dry and dustfree.

• Do not install the compressor in a damp or wet room.

• The compressor may only be used in suitable rooms

(with good ventilation and an ambient temperature from

+5 °C to 40 °C). There must be no dust, acids, vapors,

explosive gases or inammable gases in the room.

• The compressor is designed to be used in dry rooms.

It is prohibited to use the compressor in areas where

work is conducted with sprayed water.

8. Attachment and operation

n Important!

You must fully assemble the appliance before using

it for the rst time!

8.1 Installation of the air lter (7)

• Remove the transport plug (Figure 5 pos. F) and at-

tach the air lter (7) on the unit by turning clockwise

(Figure 6).

• Solve for maintenance the air lter (7) by turning coun-

ter-clockwise (Figure 6).

ADDITIONAL SAFETY INSTRUCTIONS

Safety instructions for working with compressed

air and blasting guns

• The compressor pump and lines can become very hot

during operation. Touching these parts will burn you.

• The air which is sucked in by the compressor must

be kept free of impurities that could cause res or

explosions in the compressor pump.

• When releasing the hose coupling, hold the hose cou-

pling piece with your hand. This way, you can protect

yourself against injury from the rebounding hose.

• Wear safety goggles when working with the blow-out

pistol. Foreign bodies or blown off parts can easily

cause injuries.

• Do not blow at people with the blow-out pistol and

do not clean clothes while being worn. Risk of injury!

Safety information for paint spraying

• Do not process any paints or solvents with a ﬂash point

below 55° C. There is a risk of explosion!

• Do not heat up paints or solvents. There is a risk of

explosion!

• If hazardous liquids are processed, wear protective ﬁlter

units (face guards). Also, adhere to the safety informa-

tion provided by the manufacturers of such liquids.

• The details and designations of the Ordinance on Haz-

ardous Substances, which are displayed on the outer

packaging of the processed material, must be observed.

• Additional protective measures are to be undertaken if

necessary, particularly the wearing of suitable clothing

and masks.

• Do not smoke during the spraying process and/or in

the work area. There is a risk of explosion! Paint vapors

are easily combustible.

• Never set up or operate the equipment in the vicinity of

a ﬁre place, open lights or sparking machines.

• Do not store or eat food and drink in the work area.

Paint vapors are harmful to your health.

• The work area must exceed 30 m3 and sufﬁcient ven-

tilation must be ensured during spraying and drying.

Do not spray against the wind. Always adhere to the

regulations of the local police authority when spraying

combustible or hazardous materials.

• Do not process media such as white spirit, butyl alcohol

and methylene chloride with the PVC pressure hose.

These media will destroy the pressure hose.

Operating pressure vessels

• You must keep your pressure vessel in good working

order, operate the vessel correctly, monitor the vessel,

carry out necessary maintenance and repair work im-

mediately and meet the relevant safety precautions.

• The supervisory authority may enforce essential con-

trol measures in individual cases.

• A pressure vessel is not allowed to be used if it has

faults or deciencies that can endanger workers or

third parties.

• Check the pressure vessel for signs of rust and dam-

age each time before using. Do not use the com-

pressor with a damaged or rusty pressure vessel. If

you discover any damage, then please contact the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HC08 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info