Bedienungsanleitung Scheppach HL660 (Seite 22 von 112) (Deutsch, Englisch, Französisch, Italienisch)

781858

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

22 | GB

4. Fasten the guards (E + F) together using two

Phillips head screws, clamping brackets and nuts.

m IMPORTANT!

You must fully assemble the appliance before using it

for the rst time!

10. Initial operation

Make sure the machine is completely and expertly as-

sembled. Check before every use:

• the connection cables for any defective spots

(cracks, cuts etc.).

• the machine for any possible damage.

• the rm seat of all bolts.

• the hydraulic system for leakage.

• the oil level and

• the safety devices

10.1 Checking the oil level (Fig. 17)

The hydraulic unit is a closed system with oil tank, oil

pump and control valve. Check the oil level regularly

before every use. Too low an oil level can damage the

oil pump. The correct oil level is approx. 10 to 20 mm

below the oil tank surface.

If the oil level is at the lower notch, then the oil level is

at a minimum. Should this be the case, oil must be im-

mediately added. The upper notch indicates the max-

imum oil level. The machine must be on level ground.

Screw in the oil dipstick fully, to measure the oil level.

10.2 Ventilation screw

Before operating your machine, the bleed screw (7)

should be loosened by some rotations until air can go

in and out of the oil tank smoothly. Failed to loosen the

bleed screw will keep the sealed air in hydraulic sys-

tem being compressed after being decompressed.

Such continuous compression/decompression will

blow out the seals of the hydraulic system and cause

permanent damage to your machine.

Before moving your machine, make sure the bleed

screw is tightened to avoid oil leaking from this point.

10.3 Splitting logs

Only split logs that have been sawn off straight. To do

this, proceed as follows:

1. Place the log plain onto the work table (9).

2. Your machine is equipped with Two-hands Control

System that requires to be operated by both hands

of the user – left hand controls the control lever (12)

while right hand controls the push button switch (6).

3. Simultaneously push button switch (6) to start the

splitting action.

The log splitter will freeze upon absence of either

hand.

3. Place the device horizontally on the oor, and put

the Styropor pad of the packaging underneath the

splitting wedge side.

4. Assemble the wheels on the wheel axis of the

stand.

9.2 Installing the handle (4) (enclosed accessories

bag a) (g. 5)

Fasten the handle to the U-bar with two cylindrical

screws.

9.3 Installing the protective guard (L) (enclosed

accessories bag b) (g. 6 + 7)

1. Fit the protective guard (L) to the trunk guide plate

(5) and use the enclosed cylindrical screws and

nuts to afx it.

2. Undo the cylindrical screw with washer that is lo-

cated on the wheel bracket.

3. Fasten the other end of the strut to the protective

guard using the Phillips head screw and nut. (3)

4. Now guide the open end of the strut (O) between

the washer and the wheel bracket, tighten the cy-

lindrical screw (4) again rmly.

9.4 Installing the tray table (K + M) (enclosed ac-

cessories bag c + d + e) (g. 8 + 9 + 10)

1. Attach the tray table (K) to the same side as the

protective guard (L). Use two cylindrical screws

and spring washers to afx the table to the log

splitter. (1)

2. Ensure that the table and the protective guard are

level in relation to each other.

3. Undo the screw on the left of the foot.

4. Fasten the other end of the strut to the protective

guard using the Phillips head screw and nut, align

everything and tighten the screws rmly.

5. Now guide the open end of the strut (N) between

the screw and the foot bracket, tighten the screw

slightly.

6. Repeat the process on the other side.

7. Align both tables in relation to each other and use

the Phillips head screws and nuts (e) to afx them.

9.5 Installing the guard (E - J) (enclosed

accessories bag f) (g. 11 + 12)

1. Connect the guards (H) and (I) together, use two

Phillips head screws, clamping brackets and nuts

to afx it.

2. Fasten the guards (H, I, J) to the holes provided

for this. These are on the side of the table and

the protective guard. Fasten the guard with seven

Phillips head screws, clamping brackets and nuts.

Fit the protective guard (G) to the control lever

protection (11) and use a Phillips head screw and

a nut to afx it.

3. Now fasten the guards (E + F) on the top. Fasten

them with eight Phillips head screws, clamping

brackets and nuts.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HL660 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info