Bedienungsanleitung Scheppach HL660 (Seite 23 von 112) (Deutsch, Englisch, Französisch, Italienisch)

781858

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 23

This may have the following causes:

• Passage points, where connection cables are

passed through windows or doors.

• Kinks where the connection cable has been im-

properly fastened or routed.

• Places where the connection cables have been cut

due to being driven over.

• Insulation damage due to being ripped out of the

wall outlet.

• Cracks due to the insulation ageing.

Such damaged electrical connection cables must not

be used and are life-threatening due to the insula-

tion damage.

Check the electrical connection cables for damage

regularly. Make sure that the connection cable does

not hang on the power network during the inspection.

Electrical connection cables must comply with the

applicable VDE and DIN provisions. Only use con-

nection cables with the marking „H07RN“.

The printing of the type designation on the connec-

tion cable is mandatory.

For single-phase AC motors, we recommend a fuse

rating of 16A (C) or 16A (K) for machines with a high

starting current (starting from 3000 watts)!

AC motor 230 V/ 50 Hz

Mains voltage 230 Volt / 50 Hz.

The mains connection and the extension cable have

to be three-core cables = P + N + SL. - (1/N/PE).

Extension cables must have a minimum cross-section

of 1.5 mm².

Mains fuse protection is 16 A maximum.

12. Cleaning

m ATTENTION!

Pull out the power plug before carrying out any clean-

ing work on the equipment.

We recommend that you clean the equipment imme-

diately after you use it.

Clean the equipment regularly with a damp cloth and

some soft soap. Do not use cleaning agents or sol-

vents; these may be aggressive to the plastic parts in

the equipment. Ensure that no water can get into the

interior of the equipment.

Never force your machine for more than 5 seconds by

keeping pressure on it to split excessively hard wood.

After this time interval, the oil under pressure will be

overheated and the machine could be damaged. For

such extremely hard log, rotate it by 90° to see wheth-

er it can be split in a different direction. In any case,

if you are not able to split the log, this means that its

hardness exceeds the capacity of the machine and

thus should be discarded to protect the log splitter.

10.4 Hoist limiting

It is reasonable to limit the hoist of the pressure plate

(10) for short splitting material. Thereto press the con-

trol lever (12) and the release button (6) and let the

pressure plate (10) move just in front of the splitting

material.

Release the release button now and mount the hoist

limiting ring (7a) to the housing and tighten it. After-

wards you can release the hydraulics lever.

The pressure plate will now be resting in the selected

position.

10.5 Wrongly placed log (Fig. 13)

Always set logs rmly on the log retaining plates and

work table. Make sure logs will not twist, rock or slip

while being split. Do not force the blade by splitting

logs on the upper part. This will break the blade or

damage the machine.

Do not attempt to split 2 pieces of logs at the same

time. One of them may y up and hit you.

10.6 Jammed log (Fig. 14 + 15)

Do not try to knock the jammed log off. Knocking

about will damage the machine or may launch the log

and cause accident.

1. Release both controls.

2. After the log pusher moves back and completely

stops at its starting position, insert a wedge wood

under the jammed log (see gure 15).

3. Start the log splitter to push the wedge wood un-

der the jammed one.

4. Repeat above procedure with sharper slope

wedge woods until the log is completely freed.

11. Electrical connection

The electrical motor installed is connected and ready

for operation. The connection complies with the ap-

plicable VDE and DIN provisions.

The customer‘s mains connection as well as the ex-

tension cable used must also comply with these reg-

ulations.

Damaged electrical connection cable

The insulation on electrical connection cables is of-

ten damaged.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HL660 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info