Bedienungsanleitung Scheppach HSM3500 (Seite 31 von 92) (Deutsch, Englisch, Französisch, Spanisch)

781910

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 31

6. Re-mount the saw blade guard (1).

7. Check the concentricity by briey starting up the

machine and then switching it off again.

Attention!

• Operation of the stone cutting machine is not per-

mitted without the corrective cover!

• When fastening the blade, make sure that the dia-

mond cutting wheel does not „wobble“.

• Ensure the rm seating of the water hoses on the

protective cover.

14. Transport (Fig. 23)

Caution! Disconnect power plug

Observe the following for transporting the stone cut-

ting machine:

• Lift off the roll slide (6) and transport it separately.

• Lock the cutting head unit (4).

• Empty the water tube (8) and cooling system.

• Fold the supporting feet (11) as described in (Fig.

4-7) and use the transport rollers for the transport.

15. Electric connection

Check electric cables regularly for damage. Ensure

that during the check, the connecting cable is not

connected to the mains.

Electric connecting cables must conform to the com-

mon VDE- and DIN provisions. Only use connecting

cables with the H 07 RN designation.

Keeping a copy of the type designation on the con-

necting cable is a specication

• The product meets the requirements of EN 61000-

3-11 and is subject to special connection condi-

tions. This means that use of the product at any

freely selectable connection point is not allowed.

• Given unfavorable conditions in the power supply

the product can cause the voltage to uctuate tem-

porarily.

• The product is intended solely for use at connec-

tion points that

a) do not exceed a maximum permitted supply im-

pedance “Z”, or

b) have a continuous current-carrying capacity of

the mains of at least 100 A per phase.

• As the user, you are required to ensure, in consulta-

tion with your electric power company if necessary,

that the connection point at which you wish to oper-

ate the product meets one of the two requirements,

a) or b), named above.

Damaged electric connecting cables

Insulation damages frequently occur on electric con-

necting cables. The reasons are:

• Pressure points, if connecting cables are routed

through window or door gaps.

1. Unscrew the star knob screw (e) on the cutting

head unit (4) and push the cutting arm upwards.

2. Fix the desired cutting depth with the star knob

screw (f).

3. Lower the cutting head unit (4) with the diamond

cutting wheel.

4. Leave the star knob screw (e) unscrewed.

Attention! It should be possible to lower the dia-

mond cutting wheel (14) approx. 3 mm below the

upper edge of the roll slide (6). The diamond cutting

wheel may not touch the roll slide.

Cutting with the cutting head – pivot device / mi-

tre cuts (Fig. 18-20)

Unscrew the cutting head pivot device with the lever

screw (d) and pivot the cutting head (4) 45° to the

stop. Re-tighten the lever.

Attention! Check the stop setting before you begin

cutting. The diamond cutting wheel may not touch

the roll slide.

Perform cutting as described.

Replacing the diamond cutting wheel (Fig. 21,22)

Attention! Pull out the mains plug

Caution!

• Danger of cuts on the diamond cutting wheel!

• Wear gloves when replacing the diamond cutting

wheel.

• Check the cutting wheel for direction of rotation,

concentricity and possible damage!

1. Pull out the mains plug.

2. Unscrew the star knob screw (e) on the cutting

head unit (4) and push the cutting arm upwards

completely. Lock the cutting arm with the star

knob (f) on the cutting head unit (4) (Fig. 15).

3. Unscrew and remove the four screws on the

blade‘s protective cover (1) and remove the pro-

tective cover. Note: It is not necessary to discon-

nect the water hose on the protective cover. Care-

fully fold the protective cover down.

4. Hold the cutting shaft in place with the supplied

Allen key and unscrew the clamping nut with the

open-ended spanner (included in the scope of

delivery). Left-handed thread! Carefully remove

the clamping nut, the pressure ange and the dia-

mond cutting wheel (14).

5. Before installing the new diamond cutting wheel

(14), clean the cutting shaft and the battery ange

with a rag or brush. Attention! Do not use any clean-

ing agents which can corrode the components.

Attention! When installing the new diamond cutting

wheel, proceed in the reverse sequence. Make sure

that the direction of rotation is correct! (Insert the

diamond cutting wheel – ARROW DIRECTION – in

the operating side on the ange holder). The arrow

direction on the cutting wheel and the protective cov-

er must match.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HSM3500 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info