Bedienungsanleitung Scheppach HSM3500 (Seite 29 von 92) (Deutsch, Englisch, Französisch, Spanisch)

781910

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 29

• Check the alignment of all moving parts, all bro-

ken or fastening parts, and all other conditions that

can affect smooth operation. Each damaged part

should be repaired or replaced by a technician im-

mediately.

• Do not use the machine if a switch cannot be ac-

tivated/deactivated correctly.

10. Operation

• Install the machine on an even, slide-proof oor.

• Check that the voltage on the nameplate matches

the existing voltage; connect the power plug to the

mains power supply only thereafter

• The cutting disc should be free to run before the

machine is switched on.

Caution: Cutting disc must always be cooled with

water.

Caution: Cutting disc runs with a time lag.

Do not break the cutting disc by applying pressure at

the sides.

• Under normal use conditions, the motor casing can

become hot.

• Do not use force on the machine or on an acces-

sory to achieve the performance of a bigger Indus-

trial machine. It does a better job at the output for

which it is designed.

• Dene all machine settings only when it is switched

off.

• Do not leave the machine unattended as long as

it is running.

• During shutdown, leave the machine only after it

comes to a complete standstill.

• Always switch the machine off before pulling out

the power plug from the mains socket.

• Always pull out the power plug. Never disconnect

the power plug from the mains socket by pulling

at the cable.

• Do not use cutting discs that do not meet the size

specications.

• Do not carry the machine by the cable.

Do not work with the machine if you are not sure

whether a working condition is safe of unsafe.

11. Assembly

Fig. 4-10

For packaging purposes, your machine is not fully

assembled.

1. Carefully remove the machine from the packaging

and set it aside on the ground.

2. First fold out the supporting foot (11) without trans-

port rollers up to the stop. Then lock the screw

upward in the oblong hole in order to x the foot

(Fig. 7, 8).

3. Repeat the process with the 2nd foot, with trans-

port rollers.

Do not wear loose clothing or ornaments which can

get entangled in rotating components.

Anti-skid shoes are recommended.

Protect long hair with suitable means.

Wear eye- and ear protection. Always wear:

• ANSI- approved dust masks.

• Hearing protection.

Always maintain your balance.

Do not stretch yourself over running machines.

8. Residual risks

The machine is built according to the latest tech-

nology and the recognized technical safety-re-

lated rules. Nevertheless, individual residual

risks can occur during operation.

• Danger of Injury to ngers and hands from the run-

ning tool if it is used incorrectly.

• Risk to health from dust. Wear personal protec-

tion equipment such as eye protection without fail.

• Injuries due to defective diamond cutting disc. The

diamond cutting disc must be checked regularly for

physical integrity.

• Risk of injury to ngers and hands during cut-

ting disc replacement. Wear appropriate working

gloves.

• Risk of injury during machine activation from sud-

den start of cutting disc.

• Risk from power while using improper electric con-

necting cables.

• Risk to health from running cutting disc due to long

hair and loose clothing. Wear personal protection

equipment like hair net and tight-tting working

clothes.

• Even after taking all the necessary precautions,

not apparent residual risks cannot be ruled out

completely.

• Residual risks can be minimized if the „safety in-

structions“ and the „proper use“, as well as operat-

ing instructions manual are observed jointly.

9. Before start-up

Replace cracked diamond cutting discs.

• Get to know your machine. Familiarize yourself

with its use and its restrictions, but also with the

specic potential risks.

• Check the machine carefully for damages to en-

sure that it is able to achieve the intended output.

In case of doubt, please replace the concerned

component.

• Ensure that the switch is on Off, before inserting

the power plug into the mains socket.

• Ensure that the machine is cleaned and lubricat-

ed properly.

• Before start-up, check the machine for damaged

parts and nd out whether these parts are work-

ing properly and performing their dened function.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HSM3500 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info