Bedienungsanleitung Scheppach HSM3500 (Seite 30 von 92) (Deutsch, Englisch, Französisch, Spanisch)

781910

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

30 | GB

Attention! The water pump (18) starts up automati-

cally with the drive motor (5) is switched on! You can

regulate the water ow to the diamond cutting wheel

(14) with the shut-off valve (18).

13. Operation

90° cutting (Fig.13)

1. Loosen the wing bolt (c)

2. Set angled stop (13) to 90° and tighten the wing

bolt (c) again.

3. Tighten the wing bolt (b) to x the angled stop (13).

4. Switch on the machine with the On/Off switch (2).

5. Push the workpiece against the stop (13) and slide

it against the diamond cutting wheel (14) with the

roll slide (6) and cut it is one piece.

6. Switch off the machine again.

45° diagonal cutting (Fig. 13)

1. Loosen the wing bolt (c)

2. Set angled stop (13) to 45° and tighten the wing

bolt (c) again.

3. Tighten the wing bolt (b) to x the angled stop (13).

4. Make a cut as described under „90° Cuts“.

Cutting with a xed cutting depth (Fig.15,16)

The cutting head (4) is xed in place for this cut.

The workpiece is pushed against the diamond cut-

ting wheel (14) with the roll slide (6) and cut in one

complete piece. When cutting, ensure a consistent

pressure adapted to the motor output!

1. Unscrew the star nob screw (e) on the cutting

head unit (4) and push the cutting arm upwards.

2. Place the workpiece to be cut on the roll slide (6)

and place the stationary cutting wheel (14), with a

full segment, loosely on the workpiece.

3. Pull the workpiece back with the roll slide (6) far

enough that the diamond cutting wheel (14) can

be lowered somewhat.

4. Fix the desired cutting depth with the star knob

screw (e).

5. Lock the cutting depth with the star knob screw (f)

on the cutting head unit (4).

Attention! Always hold and/or press the guided

workpiece on the corresponding workpiece stop (7

+ 13).

Caution: Wait for the cooling water to reach the cut-

ting disc (14).

Cutting with a non-xed cutting depth (Fig. 17)

A non-xed cutting depth is recommended for easier

cutting of larger cutting depths. In the process, less

stress is placed on the motor (5) and the diamond

cutting wheel (14) is preserved.

The workpiece is moved back and forth with the roll

slide (6) under the non-xed cutting head for this cut.

In the process cutting head (4) is pressed downward

with the right hand.

4. Place the machine on the feet.

5. Place the water pump (18) in the holder of the wa-

ter tube and insert the sealing plug in the drain of

the water tube (8). (Fig. 9,10)

6. Fill the tube with water so that the pump (18) is

covered with water at all times (also during oper-

ation).

Attention!

The water pump may never run dry. It must always

be covered with water during operation.

Mounting the roll slide (Fig. 11)

1. Place the roll slide (cutting table) (6) on the roll

table guide rail (9); in the process, the frame (a)

of the two right guide rollers covers the guide

rail. Simply place the two left guide rollers on the

guide rail.

2. When you are standing in front of the stone cut-

ting machine, the scale must face towards you.

The 90° cutting wheel gap is to the left in the roll

slide (6), the 45° cutting wheel gap is to the right.

3. The cutting table must roll easily. Make sure that

all four rollers are on the guide rail (9).

Mounting the lever screw for the cutting head

pivoting device (Fig. 12)

1. Remove the hexagon screw with a 30 mm

open-ended spanner.

2. Fit the lever screw (d) of the cutting heat pivoting

device on the thread and tighten it.

Mounting the longitudinal aligning stop (Fig. 13)

1. Place the longitudinal aligning stop (13) on the

stop rail with scale (7) on the roll slide (6).

2. Align the longitudinal aligning stop (13) at the ap-

propriate distance to the cutting wheel (14).

3. Fix the longitudinal aligning stop (13) by tightening

the locking lever (b)

12. Start-up

On/Off switch (Fig. 14)

To activate the machine, press the „I“ of the On/Off

switch (2).

Before starting the cutting operation, you must wait

for the cutting disc to reach its max. speed and for

the cooling water pump (18) to pump water to the cut-

ting disc.

To deactivate the machine, press the „0“ of the switch

(2). (Fig. 14).

Note:

After switching on the saw, rst pay attention to the

direction of rotation of the diamond cutting wheel.

Observe the direction of the arrow on the machine!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HSM3500 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info